A= 25B= 75C= 5D= 45E= 85F= 8 Problem 4. The table below shows the data for the series of test in a consolidated undrained test of the sample.Test12Chamber pressureA kPaВ КРаС КРаD kPaE КРаF kPaDeviator stressPore water pressurea. Determine the angle of internal friction for undrained conditionb. Determine the cohesion at undrained condition.c. Determine the angle of internal friction for drained conditiond. .Determine the cohesion at drained condition.

Answered: Image /qna-images/answer/a31b105f-6f8e-48c8-9cc3-f305f1d00cad.jpg

a. Determine the angle of internal friction for undrained condition b. Determine the cohesion at undrained condition. c. Determine the angle of internal friction for drained condition d. .Determine the cohesion at drained condition.

a. Determine the angle of internal friction for undrained condition b. Determine the cohesion at undrained condition. c. Determine the angle of internal friction for drained condition d. .Determine the cohesion at drained condition.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.19P

See similar textbooks

Similar questions

A CID TXC test was performed on a sample of sand. At the end of consolidation, the back pressure was 140 kPa, and the cell pressure was 340 kPa. At failure, the deviator stress was (ơ1 – 03)f = 200 kPa. a. What was the total pore water pressure, u, at failure? b. Calculate the principle effective stresses, ơi' and os', at failure. c. Calculate the friction angle, d', for this soil.
الشعبة In direct shear test, The area under shear gradually increases as the test progresses. ● ● the stress distribution on the failure plane is uniform none of them In direct shear test continuo talin الاسم/
d) An oedometer test was also performed on a (saturated) reconstituted sample obtained at the site. The initial void ratio was calculated as 1.005 and the initial sample height was 20 mm. The following measurements were reported for each of the 24-hr stress increments: Table 4. Oedometer test measurements Normal stress (kPa) 1.5 13 26 52 104 208 416 Change in sample height (mm) 0.419 0.199 0.229 0.209 0.208 0.199 Plot the evolution of the void ratio resulting from the data above using semi-logarithmic axes (i.e. produce an e-log o'y plot). Is there anything you can comment on the stress history and consolidation state of the soil?
3. In a drained tri-axial test, a specimen is confined under pressure and axially loaded until failure. The failure conditions of the specimen are analyzed for shear strength. What is the value of the minor principle stress? Half the value of the major principle stress Twice the value of the major principle stress . The same as the confining pressure The same as the cohesion value ● ● ●
Table Q3(c) presentssamples information for point load test. Based on the data: (i) Calculate the Unconfined Compression Strength for sample A and B. (ii) Classify the strength of sample A and B based on Bieniawaski 1975 classification as given in Table Q3c(ii). (iii) As an engineer, define the reason of strength classification of sample A and B.
A series of identical samples have been tested with drained triaxial test and some of the values are given in the tabulated table 3(Below). Calculate the remaining values as in the blank box. PARAMETER |cell pressure, o3 (kPa) total axial stress, 01 (kPa) pore pressure at failure, u¡ (kPa) |change in volume, Av effective cell pressure, o3' (kPa) effective total axial stress, o,' (kPa) |difference in stress, q (kPa) CD test 150 284 i 1.8 ii i iv O i = 134; ii = 16; iii = 150; iv = 0 O i = 134; ii = 284; iii = 150; iv = 0 O i = 0; ii = 16; iii = 150; iv = 134 O i = 0; ii = 150; iii = 284; iv = 134
The unconfined compression test sampler is : Split Spoon sampler Sonotube sampler Shelby tube sampler
Name.. Q3 Water flows through the constant head setup in the laboratory, as shown in the figure, where two identical dense sand samples A and B are placed-one horizontally and the other vertically. The samples are 50 mm diameter and 100 mm in length. The water levels in the left and right sides are maintained at the levels shown, ensuring constant head throughout the test. The void ratio of the sand is 0.92 and the specific gravity of the grains is 2.69. If 165 g of water was collected in the bucket within 15 minutes, 1. What is the permeability of the soil? 2. What the pore water pressure and vertical effective stress at the mid height of sample B? OH 2 190 100+100 A = (50) 7 9 = 0.95 1963.5 100 mm crosesection מות 190 Datumn 40 mm 100 min Arey B.
Compute for the modulus of rupture of the concrete beam sample if the size of the sample is 6"x 6", and the span length of the beam (support to support) is equivalent to the 3 times the depth of the beam. Load applied is 65.5 kN at center. о 12.7 МРа о 13.1 МРа o 14.9 MPa о 11.6 MPа
Find the angle of internal friction for the sand specimen, if the deviator stress at failure is 100kPa, the cell pressure is 50kPa.if the sample is a dry sand specimen put through a triaxial test. A 30' в 15° C 45' D 37'
4. Flow net is used for the determination of (a) Quantity of seepage (b) Hydrostatic pressure (c) Seepage pressure (d) All of them. 5. Both the shear stress and the normal stress on the plane of failure are measured directly in (a) CD triaxial shear test (b) CU triaxial shear test (c) Direct shear test (d) Unconfined compression test 6. In a consolidated undrained test on an over-consolidated clay, the volume of the soil sample during shear: (a) decreases (b) first decreases and then increases (c) first increases and then decreases (d) remains unchanged.
3- A sand sample is subjected to drainage cutting test with a hollow cylinder device. Rupture occurs with increasing internal pressure while external pressure is constant. At the moment of rupture, the external stress is 200 kPa and the internal stress is 300| Kilopascals - be. Internal and external radii of the sample are 40 and 60 mm. A) Obtain the angle of soil friction. B) At the moment of rupture, what is the axial stress applied to the sample?