A wye delta transformer has a turn ratio of 2:1.It has a secondary line voltage of 480V.the secondary is connected to a wye connected three phase resistive load of 50ohm in each phase. What is the secondary phase current?

A wye delta transformer has a turn ratio of 2:1.It has a secondary line voltage of 480V.the secondary is connected to a wye connected three phase resistive load of 50ohm in each phase. What is the secondary phase current?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.5MCQ: For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is...

See similar textbooks

Related questions

Q: Consider a bar of p-type silicon that is uniformly doped to a value of N₂ = 2 × 10¹6 cm-3 at T = 300…

A: Given: Na=2×1016 cm-3, T=300 K, Applied electric field is "0",δp0=δn0=2×1014 cm-3, μn=1200…

Q: In a silicon sample at equilibrium the Fermi level is located above the middle of the band gap by…

A: As per the given question, energy bandgap for given data is given below.

Q: Given the circuit described by the equation Q" +3Q' + 100Q = 5 cos 10t - 5 sin 10t, O Find the…

Q: Find the resistor values of R1 and R2 to have VR1 = 9VR2

A: here we have to find the resistances R1 and R2 .

Q: A cube with 2 m sides (0< x, y, z <2 m) carries a charge with density p, 12xyz mC/m³. (a) Calculate…

A: Given, length of side of cube, l=2 m surface charge density, ρv=12xyz C/m3

Q: 1. Design an inverting amplifier with a gain of 6 and input impedance of 5km. Draw the schematic…

Q: The critical frequency of an ionospheric layer is 10 MHz What is the maximum launching angle from…

Q: Using the defining equations, compute the inverse Fourier transform of the following signals: (Part…

A: Given: X1jω=jδω-ωc-δω+ωc and X2jω=δω-ωc+δω+ωc. Required: Inverse Fourier transform.

Q: Example Find the transfer function of system R(s) G₁(s) G₂(s) G3(s) G4(S) - -1 C(s)

Q: Alternator and Synchronous Motors A 3-phase alternator has 48 stator slots and 4 poles. Calculate…

A: Given- 3-phase, 4-pole alternator, Number of stator slots=48, To Find- The distribution factor for…

Q: The output voltage range of the op amp in the following figure is equal to the power supply…

A: In this question, We need to determine the output voltage of the op amplifier. We are solving this…

Q: Logic Function X = (AB+C)(B+C) Logic Diagram with Gates

A: Given, The given logic function, X=AB+C¯B¯+C

Q: Consider the network to the right, with the following value R₁ = 50 R₂ = 30 R3 = 40 R4 = 80 R5=202…

A: It is given that: R1=5 ΩR2=3 ΩR3=4 ΩR4=8 ΩR5=2 ΩR6=6 ΩVo=36 V

Q: (a) Initially, the temperature of the filament is 20°C and there is no current flowing through it.…

A: Given that, Length of Conductor (L)=580 mm. Radius of Conductor (r)=23 μm. Resistivity of Conductor…

Q: 4) For the given the amplifier circuit shown below has the following parameters: Rid = 20k2, ro =…

A: According to the question, for the given circuit as shown below We need to find

Q: For the given circuit below, it operates on a peak- to-peak input voltage of 133.1 V, F = 60 Hz…

A: Given: Peak to Peak input voltage = 133.1V Number of turns in Primary N1 = 10 Number of turns in…

Q: 3. A regular_ tetrahedron has vertices at P₁(2,0,0), P₂(-1,√3,0), P3(-1,-√√3,0), and P4(0,0,2√2).…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: In a two-element series network, the instantaneous voltages across the elements are sin 314 t and…

A: Given- Instantaneous voltages, V1=sin 314t=1∠0° V.V2=32 sin 314t=32∠45° V. To find- The resultant…

Q: for 9VR2 + VR2 20 how u get 10VR2VR2? Did you divide 20v into 2 base on vr2vr2

A: If you take common as VR2 and on addition of 9 and 1 we get 10. I,e VR2(9+1) And then by dividing…

Q: Problem 3 Consider the resistive circuit shown in the figure below, Vd = 300 V and R=75 £2. The data…

A: Given that, Vd=300VR=75 Ωton=150 nstoff=300 ns Here we have to find out voltage across the switch,…

Q: Carrier Statistics Example 3.6 (a) Determine the location of Fermi level, with respect to Ec and Ey,…

A: We need to find out position of Fermi level with respect to Ec and Ev .

Q: A. Compute the state equations for the discrete-time closed-loop system. Notice that the input is…

A: Given that, Gp(s)=2s(s+2), Sampling time (T)=0.5s. Here we have to find out the state equation of…

Q: In free space, E = through surface 12pzcos da, 12pzcos da - 6pzsin da, + 6p²cos pa, V/m. Find the…

A: Given data: E=12ρzcosϕaρ-6ρzsinϕaϕ+6ρ2cosϕaz V/m

Q: Question 3 a) The conductors of a three-phase transmission line are arranged in the form of an…

A: Given that, R=2.07Ω, L=310.8mH, C=1.477μF, f=50Hz We have to find here is sending end voltage and…

Q: In the circuit shown in the given figure N is a finite gain amplifier with a gain of k,a very large…

Q: input 1 1 1 impurtro inio Present State @Find Q 0 4 11 input: 0 a insh Clo inel by 1 inct Next store…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Problem 3 An electric table saw, a wood shaper, and a motor load of a workshop establish an 18 kVA…

A: Apparent Power is the result of combining Active and Reactive Power. It is the circuit's overall…

Q: stion 1-) Write the state equations for the circuit given in Figure below.

Q: An non transistor has a beta cut-off frequency fBof 1 MHz, and common emitter short circuit…

A: Given: fβ=1 MHz and β=200. Required: Unity gain frequency fT and alpha cut-off frequency f0.

Q: Three loads A, B, and C are connected in parallel across a 1.5-kV-rms 60-Hz Source, as show below.…

A: First calculate active and reactive power of each load . Power delivered by source = sum of the…

Q: What is the relationship of the ignition angle to the average value of the output voltage?

A: Given: Ignition angle and output voltage

Q: In the given figure, A₁, A₂ and A, are ideal ammeters. If A₂ and A, read 3 A and 4 A respectvely,…

A: Here we have to find reading of A1 .

Q: Objective 1-Use voltage and current constraints in an ideal op amp 5.1 Assume that the op amp in the…

A: The required parameters can be calculated by using the inverting amplifier gain expression and the…

Q: Question 7 A cell has an internal resistance of 0.02 ohm and an e.m.f. of 2.0V. Calculate its…

A: Resistance (R) = 0.02 Ω EMF = 2 V

Q: A 3-kW resistance heater in a water heater r

A: Given that: The power of heater, P = 3 kW It runs for 2 hours to raise the water temperature to the…

Q: For the cascaded system of Fig. 5.178, determine: a. The loaded voltage gain of each stage. b. The…

Q: Consider the constellation shown in the attched image and calculate the probability of a symbol…

Q: If the voltage waveform is applied to a 20-mH inductor, find the inductor current (0) for 0<t<2 s.…

A: Given, voltage waveform across the inductor L = 20 mH To find the inductor current i(t) for…

Q: Use the complex differentiation property and the transform of the unit ramp to obtain the…

Q: 2. Solve for vo 12 V | 32 8 Ω 60 2%

A: We need to find out the output voltage for given circuit. We will find out it by using of nodal…

Q: A 3-phase, star-connected alternator generates 6,360 V per phase and supplies (514) kW at a pf…

A: As we know that the transformer works on the principle of electromagnetic induction where the input…

Q: The field coils of a six-poles D. C. Generator, each having 600 turns, are connected in series. On…

A: Here we have to find the average voltage induced across the field terminals.

Q: USE THE CIRCUITS IN THE S-DOMAIN The parameter values for the circuit in are as follows:…

A: Given: R=1kΩ, L=12.5H, C=2μF, and Idc=30mA.

Q: Question: If the output power from an audio amplifier is measured at 100W when the signal frequency…

A: Solution:- Initial output power = 100 W Final output power = 1 W f = 10 KHz

Q: Show how to make a 4-to-1 MUX, using an 8-to-1 MUX.

A: MUX: it is a combinational circuit which can be used as a serial to parallel converter. Generally…

Q: A square-wave inverter has an RL load with R = 152 and L = 10 mH. The inverter output frequency is…

Q: Identify the type of Transformer referred to K=0.7 a. Step down b. Voltage transformer c. Step up

A: Given data, Turn ratio k = 0.7.

Q: USE THE CIRCUITS IN THE S-DOMAIN, The circuit parameters in the circuit are R=5kΩ;L=200mH; and…

Q: 4. Calculate is from the following circuit. 20 10V 402 5 ww 80 102 • 4Ω 402 6Ω 202

Q: Based on the datasheet of SCR MCR3835-10 its VRRM is 800 V. So, what is the largest AC voltage that…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
The rated voltages of a single-phase transformer are 2000 V and 200 V in its primary and secondary respectively. The shunt impedance can be modelled with a resistance of 14000 ohms in parallel with a reactance of 1100 ohm, both refer to primary side. The primary and secondary series impedances are (0.12+j 0.35) ohms and (0.0012+j 0.0035) ohms respectively. A load is connected to the secondary side of transformer, draws 810 KVA with a lagging power factor of 0.85. The load voltage is same as rated voltage, that is 200 V. ▪ Use per unit method for analysis and find the voltage on primary side in pu.
QUESTION 12 A single phase 600v/120v transformer has a load of 30 ohms resistive and 20 ohms inductive in series. what is the load power factor? O O O O O .91 O .39 .83 .42
A three phase power transformer having a line voltage ratio of 400 V to 33 kV is connected in star-delta. The C.T.s on 400 V side have current ratio as 1000/5. What must be the C.T. ratio on 33 kV side. Assume current on 400 V side of transformer to be 1000 A. C.T. secondaries in delta p 5A oooo oooo 5√3 A -0000 0000 0000 0000 Star-delta transformer 0000 5√3 A vooo னள். m reeee p C.T. secondaries in star 5√3 A 0000
A 50 kVA transformar has a core loss of 500 W and full load core loss of 900 W. The load at which the efficiency is maximum is ?
A three-phase transformer bank is connected wye–delta. The primary voltage is 12,470 V, and the secondary voltage is 480 V. The total capacity of the transformer bank is 450 kVA. One of the three transformers that form the three-phase bank develops a shorted primary winding and becomes unusable. A suggestion is made to reconnect the bank for operation as an open-delta. Can the two remaining transformers be connected open-delta? Explain your answer as to why they can or why they cannot be connected as an open-delta. If they can be reconnected open-delta, what would be the output capacity of the two remaining transformers?
2) 9.2Three - 25 KVA single-phase transformers are connected in delta – delta. One of the transformers has been defected. What is the maximum real power that the transformer bank can deliver at a power factor of 0.8?
Three single phase transformers are connected in a Delta-Wye configuration. Each transformer is rated 13kV/64kV. The transformers are connected to a 3 phase 13kV (L-L) supply and the balanced three phase load is 788KVA. What is the current magnitude in the secondary winding of each transformer? explain the steps too please
A 4 kVA, 400/200 V single-phase transformer has resistance of 0.02 p.u. and reactance of 0.06 p.u. Its actual resistance and reactance refferd to h.v. side are ?