A voltage of 100<0° V(rms) is across an impedance of 5 + j2 N. a) What type of impedance is this (capacitive, inductive, or purely resistive)? b) Determine the current in the circuit; c) Draw the phasor diagram showing voltage and current; what is the phase relationship between current and voltage? Is this consistent with your answer to part a)?

A voltage of 100<0° V(rms) is across an impedance of 5 + j2 N. a) What type of impedance is this (capacitive, inductive, or purely resistive)? b) Determine the current in the circuit; c) Draw the phasor diagram showing voltage and current; what is the phase relationship between current and voltage? Is this consistent with your answer to part a)?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Q2. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. a = 50° TI 50 2 Vs = 300 sin 100zt ( cot T2 in cot
Fill in the table for a correctly wired duplex outlet (U.S. National Electric Code standards for voltage PARAMETER EQUATION and frequency). Note the used of double- subscript notation. You can assume a 0° phase reference for Vba(t). Vba(t) Vea(t) Vbe(t) Vba (Peak Phasor) Vea (Peak Phasor) Vbc (Peak Phasor) Vba (RMS Phasor) Vea (RMS Phasor) Vbc (RMS Phasor) A C
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
1. a) Sketch the phasor diagram, using current as the reference phasor, for a load consisting of a resistor and capacitor in series. b) Sketch the phasor diagram, using current as the reference phasor, for a load consisting of a resistor and inductor in series.
(b) An inductive load consisting of resistor, R and inductor, L in series feeding from a 240430° Vrms, 50 Hz supply consumes 6 kW at lagging power factor of 0.88. (i) Determine the current through the load. (ii) Find R and L. (iii) Draw the phasor diagram of supply voltage and current.
Complete and clear solution pls. Sinusoidal voltages and currents
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
The circuit shown in Figure Q1.2 is connected to a 1.6 Hz sinusoidal source. Calculate the total impedance of this circuit. 0.52 99.5mH 49.7 mF Figure Q1.2 mm.
Suppose I have two peak phasor voltages, V, = 100245° and V, = 75Z-60°. Circle Your Choices: I. The frequencies associated with the phasors are (0 Hz, 60 Hz, 50 Hz, Unknown). II. The rms value of the first phasor is (100, 70.7, 141, 200) volts. III. If you want to add these two phasors, the frequencies must be (60 Hz, 50 Hz, The same, Integer multiples of a given frequency.)
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002
If, in one (360 degrees), all of the instantaneous power falls under positive loops (no negativeloops), the load must be:a. A resistorb. An inductor or capacitorExplain:
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1