a) Two thermal generator units have the following incremental cost curves then determine the ECONOMIC LOAD SCHEDULING between the generators for total load(PD) of 50 MW,65 MW,85 MW,110 MW and 150 MW. When load is zero, the cost of production of the generators are 100 and 180 respectively. Assume both generators are operating at all times and power loss is neglected. Also, Calculate Cost of production in each case. F1= 0.22 + 0.16 P1 Unit 1: Min 25 MW, Max 90 MW: F2= 0.48 + 0.41 P2 Unit 2: Min 15 MW; Max 75 MW

a) Two thermal generator units have the following incremental cost curves then determine the ECONOMIC LOAD SCHEDULING between the generators for total load(PD) of 50 MW,65 MW,85 MW,110 MW and 150 MW. When load is zero, the cost of production of the generators are 100 and 180 respectively. Assume both generators are operating at all times and power loss is neglected. Also, Calculate Cost of production in each case. F1= 0.22 + 0.16 P1 Unit 1: Min 25 MW, Max 90 MW: F2= 0.48 + 0.41 P2 Unit 2: Min 15 MW; Max 75 MW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 1200 kW,60 Hz synchronous alternator A identical governor droop of 0.0005 Hz/kW.Machine A takes two third of 1000kW bus load at 60 Hz.lf an additional 800 kW load is connected to the bus determine (a) bus frequency (b) load on each machine. is in parallel with a 400 kW,60 Hz alternator B.Both machines have (a) 58.6 Hz (b) 566.67 kW, 433.33 kW. (a) 59.6 Hz (b) 866.67 kW, 133.33 kW (a) 59.8 Hz (b) 666.67 kW, 333.33 kW (a) 58.9 Hz (b) 766.67 kW, 233.33 kW
Two identical 20 MW three-phase alternators operate in parallel. The governor of first machine is such that the frequency drops uniformly from 50 Hz on no-load to 48 Hz on full load. The corresponding uniform speed drop of the second machine is from 50 Hz to 47.5 Hz. How will the two machines share a load of 30 MW?
b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (1) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
For a power station the yearly load duration curve is a straight line from 50,000 to 4000 kw. To meet the load three turbogenerators are installed. The capacity of two generators is 20,000 kw each and the 3rd is rated at 7,000 kw. a. Draw the annual load duration curve b. Determine the following the Energy generated per year, Load factor and Annual Capacity factor.
A generator is feeding the load. A second load will then be connected in parallel with the first load. The generator has an idle frequency of 61Hz and an Sp slope of 1MW/Hz. Load2 draws 800kW active power at 0.707 reverse power factor, while load1 draws 1000kW active power at 0.8 reverse power factor. What will be the operating frequency of the system after load 2 is connected? *Please explain the solution step by step
Two identical 2000 kVA alternators operate in parallel. The governor of the first machine is such that the frequency drops uniformly from 50 Hz at no-load to 48 Hz at full-load. The corresponding uniform speed drop of the second machine is 50 Hz to 47.5 Hz. What is the maximum unity pf load that can be delivered without overloading either machine
Two 60MVA, alternators operate in parallel. The setting of the governor are such that the rise in speed from full load to no load is 2% in one machine and 3% in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 120MW, what will be the load on the first machine (with 2% speed regulation) when the total load is reduced to 80MW?
A synchronous generator is rated 645 MVA, 24 kV, 0.9 pf lagging. It has a synchronous reactance 1.2 . The generator is feeding full load at 0.9 pf lagging at rated voltage. Calculate: (a) Excitation emf (E,) and power angle & (b) Reictive power drawn by the load Carry out calculations in pu form and convert the result to actual values.
Refer here for the specifications of the D400. a) What power output should you be able to supply from the 24V D400 at 15.4 m/s? b) If the wind drops to 2 m/s, what will the output power be? c) According to the performance graph what is the maximum power you can obtain from the 24V D400? There is a possibility of installing the turbine on top of a 20m high mast instead. Assuming that Zo=0.012, what would you expect the wind speed to be at that height? Use wind shear formula and assume Vref = 7.5 m/s at a height of Zref =10 m.
2.2 A three-phase synchronous generator has a reactance of 1.5 p.. and negligible resistance. It supplies a rated current of 1.0 p.. at 1.0 p.u. terminal voltage to a lagging load of 0.9 power factor. Determine the rated excitation voltage in p.u. and the internal load angle. Construct the performance chart of the generator in 2.1 (above) assuming its rating is 450 MVA.
a) Two thermal generator units have the following incremental cost curves then determine the ECONOMIC LOAD SCHEDULING between the generators for total load(PD) of 50 MW,65 MW,85 MW,110 MW and 150 MW. When load is zero, the cost of production of the generators are 100 and 180 respectively. Assume both generators are operating at all times and power loss is neglected. 7ww F1= 0.22 + 0.16 P1 Unit 1: Min 25 MW, Max 90 MW: F2= 0.48 + 0.41 P2 Unit 2: Min 15 MW; Max 75 MW b) b) Calculate Cost of production in each case.
. Two dc shunt generators A and B are rated at 100 and 150 kW at 110 V respectively, Their external load characteristics may be considered as straight line. The voltage drop In the terminal voltage from no-load to full-load Is 10 V for A and 20 V ſor B. Determine the operating voltage when these generators are operated in parallel to supply a load of 220 kW.