Dexter is preheating her oven before using it to bake. In moisture content determination, what is the importance of preheating the oven before the  analysis?

Q: A wooden block in the form of a rectangular prism floats with its shortest axis vertical. The block…

A:

Q: 6. Three points A, B, C are marked on the centerline of a roadway. Line AB has an upward slope of…

A: Option (b) is most appropriate.

Q: B '6' 10 ft 4 T Figure 2-86 40 k 12 h

A: To find the reaction components-

Q: 37. The following offsets are taken from a survey line to a curved boundary line: 5 10 15 20 30 40…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: The cantilever beam is subjected to a concentrated load P. The cross-sectional dimensions of the…

A:

Q: e made from mild steel, are used to resist the tension forces in concrete. They also control…

A: To increase the shear capacity of the erection anchor in thin panels, shear bar is employed. At the…

Q: The cable supports a railway bridge between two tunnels. Given: Distributed load, w = 1.19 MN/m…

A: Given Data Uniformly distributed load=1.19 MN/mAllowable cable tensionTAllowable=47 MNDistancea=24…

Q: Determine the magnitude of the pin force at A. Assume W = 730 lb, a = 3.2 ft, b = 2.6 ft, r = 8 in.…

A: The given figure is shown below:

Q: A nozzle is so shaped that the velocity of flow along the centreline changes linearly from 1.5 m/s…

A: Reference : Fluid mechanics, Fluid Kinematics related with Total acceleration of Fluid. We define…

Q: Consider joint C next. The Free-Body diagram is shown. All members are assumed to be in tension. Use…

A:

Q: 5 F B 100 KN C 125 kN 4 at 6 m = 24 m H D 50 kN 4.5 m E

A:

Q: Problem #8: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected…

A: Find the value of load P and axial deformation?

Q: 6. What is the bending moment (BM) & Shear force (SF) - Explain.

A: Bending moment- (BM) When an external force is applied to the element causing the element to bend…

Q: Calculate the forces in members AC, AD, and DE for the loaded truss. Restraining link BC is…

A:

Q: 1000 mm 50m 300 mm Determine the centroidal moment of rtia about the X axis.

A: Given:

Q: 1. Locate the center of gravity of the figure with respect to the X and Y axes. 2. Calculate the…

A:

Q: 5 M B И ЧИ C

A:

Q: What is the usual value of the stadia interval factor (K) ? A) 200 B)50 C)150 D)100

A:

Q: A simply supported beam AB of span 4 m is carring a triangular load varying from zero at A to 5 kN/m…

A:

Q: The beam has a span of 5 m and spaced at 2 m center to center of the beam with a yield stress for…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Method of Joints: Method of joints is one of the methods which is used in structural analysis to…

Q: A force of 110 N inclined 17.4°º from the horizontal accelerates a 6.1 kg block at 8.25 m/s² along a…

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A:

Q: The platform is rotating such that, at any instant, its angular position is 0 = (0.21t³ -0.22t² + 3)…

A:

Q: 4. Determine y in the figure so that the flashboards will tumble only when water reaches their top.…

A:

Q: The biaxial stress system in an element is shown in the figure. Which of the following will give the…

A: Given- biaxial stress system-σ1=60 N/mm2σ2=-40 N/mm2θ=45o

Q: In determining the stadia interval factor (K) of a transit, a stadia rod was held vertically at…

A:

Q: The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam…

A: Given, b = 0.80 in h = 7.5 in t = 0.50 in  P = 2750 lbs τal = 14000 psi σal = 20000 psi

Q: A magnesium-alloy Prob. 3.4-6. diameter d rod (E = 6.5 x 10 ksi) of 15 x 1 in. is encased by a brass…

A:

Q: W Determine the allowable shear stress if W= 33,813lb. 2 ft R₁ 4W 6 ft R₂ 2 ft W ΝΑ 1 in 6 in 1 in 1…

A:

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

A: Given data in question  Diameter  Length Rigidity modulus = 12×106 psi Shear stress To find out  T0…

Q: The angle between a 5-m full station of a certain curve is 10°. The curve has 7 intermediate…

A: Sta. PC = 10+300 Angle between a 5-m full station of a certain curve = 10° Number of stations = 7

Q: Station 123+00 124+00 125+00 Left/Gauche C5.25 16.50 C3.50 13.00 C0.50 7.00 Centre C5.75 C9.50 C0.50…

A: form the data given:b= 12m1) Side slope of the section;b= 12m,half width= 12/2= 6m.for 123.00…

Q: A standard specimen of cohesionless sand was tested in triaxial compression test and the sample…

A:

Q: A simply supported wood beam AB with span length L = 3.5 m carries a uniform load of intensity q =…

A: Given data in question  UDL Span member length  Cross section  To find out  Maximum flexural stress

Q: In a drained tri-axial compression test, a sample of sand fails at deviator stress of 150 kPa under…

A: Given:Sand failure stress is150 kPAConfining pressure applied is 50 kPA

Q: For water supply of a town, water is pump from a river 3 km away into a reservoir is 20 m. The…

A:

Q: For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A…

A:

Q: A two-phase signalized intersection is designed with a cycle time of 100 s. The amber and red times…

A:

Q: long A log 30 cm in diam. and Im is thrown into the water. If its sp. gr. is 0.75, what is the depth…

A: Given data,  Diameter (d)=30cm   Height (H)=1m=100cm   Specific gravity of body= .75 To calculate…

Q: A solid shaft is subjected to a bending moment of 3 kNm and a twisting moment of 4.5 kNm. Find the…

A:

Q: 4) (a) Solve the following indeterminate beam by the moment distribution method. Determine the…

A:

Q: AZIMUTH AB=S101*26'32" ; ANGLES TO THE RIGHT ABC= 50*54'26", BCD= 38*36'38". FIND THE AZIMUTH FROM…

A: Given that :

Q: A highway curve was designed to connect intersecting tangents intersecting at an angle of 72°. The…

A:

Q: A spillway is to be designed for a flood control reservoir. The design must pass the 200 year event…

A: Given :

Q: ਕਰ ਸ Elementos TAB = TBC = TBD TAD = TDC = TED= 6m 135 kN B D ( ) ) 6 m 67.5 kN 1.5 m 1.5 m 1.5 m…

A:

Q: A solid cylindrical shaft has a diameter of d = 20 mm and is made from steel with an ultimate…

A: Given data:- The given Solid cylindrical shaft has a diameter, d=20 mm The Ultimate Strength, Su=850…

Q: Find the forces in members EF, KL, and GL for the Fink truss shown. Forces are positive if in…

A: To Determine Force in members EF, GL & KL.

Q: 7 ft A 4 ft B 50 lb -5 ft- 4 ft C -3 ft 100 lb D

A:

Q: Q- 7 If the slope of a chanel is 1/225 and 1/625. Then find the ratio of the discharge for this…

A: Given data-  slope of a chanel-S1= 1/225 S2=1/625To Find-The ratio of the discharge

Soil engineering for highway design

Soil engineering is a part of geotechnical engineering that deals with the characteristics of soil. It also helps to understand the behavior of the soil in different conditions. The basic concepts of soil are studied to check the strength, compressibility, and porosity of the soil. This makes soil engineering an important topic for civil engineering.