A tension member splice is made with 14-inch E70 fillet welds as shown in Figure 5. Each side of the splice is welded as shown. All steel is A36. Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 1.5. Note: Assume that the base metal shear strength is adequate (check the yielding strength for the gross area, fracture strength for the effective net area, weld strength and block shear strength). PL 5/8x8 4 in. Figure 5 2 PL 7/16x4

A tension member splice is made with 14-inch E70 fillet welds as shown in Figure 5. Each side of the splice is welded as shown. All steel is A36. Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 1.5. Note: Assume that the base metal shear strength is adequate (check the yielding strength for the gross area, fracture strength for the effective net area, weld strength and block shear strength). PL 5/8x8 4 in. Figure 5 2 PL 7/16x4

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.13P

See similar textbooks

Similar questions

Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
Question 6 Two plates of Steel A72 Gr 50 are connected with each as shown in Figure 5. E70XX Electrodes were used and 7/16 in fillet weld were made by SMAW process. What is the design strength of the weld by LRFD and ASD? E10 in - 10in P, or P. - PLx 10 Figure # 4
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A flat bar used as a tension member is connected to a gusset plate. Size of weld is 6 mm, with an ultimate tensile strength of 185 MPa. E 70 electrodes Thickness of plate = 6.25 mm. Use ASD. Thickness of gusset plate = 9.5 mm. Fy = 248 MPa Fw = 0.60(485) Fu = 400 MPa Questions: The connected parts are of A-36 steel and assumed that the tensile strength of the member is adequate: a) Determine the strength of the connection per mm considering the design shear strength of the 6 mm fillet weld. b) Determine the base metal shear strength per mm. c) Determine the available strength of the connection.
O A fillet-welded joint of 6mm size is shown in the figure. the welded surfaces meet at 60-90 degru and permissible stress in the fillet weld is 108 MPa The safe load that can be transmitted by the joint is fस Elcomm 7 f
For the L8X6X3/4 angle shown below, determine the design tensile strength considering gross yielding and net fracture. The angle is A36. Welds are longitudinal and transverse.
A tension member splice is made with 14-inch E70 fillet welds as shown in Figure 5. Each side of the splice is welded as shown. All steel is A36. Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 1.5. Note: Assume that the base metal shear strength is adequate (check the yielding strength for the gross area, fracture strength for the effective net area, weld strength and block shear strength). P PL 58x8 1 4 in. Figure 5 a. Use LRFD. b. Use ASD. 2 PL 7/16x4 P
A steel side plate is welded to a vertical steel column according to the specifications in Fig. 1. An E 70 welding electrode is used, and there is an applied load of F = 20 kN. %3D What weld size, s, is needed for a safety factor of 2 guarding against yield? F B, 150 C 100' - 200 Dimensions in millimeters Figure 1: Side plate welded to a vertical steel column.
A 180 mm x 90 mm x 10 mm angular section is welded to a gusset platehaving a thickness of 12 mm as shown in Figure ST - 100. An A 36 steel is used withFy = 248 MPa with an E70 electrodes fillet welds with Fu = 485 MPa. 1. Compute the value of P if the thickness( size ) of the fillet weld is 8 mm. 2. What is the minimum thickness of the fillet weld that can be used? 3. Compute the value of x if the thickness( size ) of the fillet weld is 8 mm.
1.12 A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108 MPa. The safe load that can be transmitted by the joint is 100 mm F F 810 50mm
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.
Determine the tensile strength of the welded A992 WT4×20. WT4× 20 PL – Transverse weld
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm