A small hydraulic Press has input piston of radius 5 cm and output piston of radius 22 cm. The output piston is connected to a pressing plate of area 8.6 cm If the input force is F, =230 N, calculate the compressive Stress in ePa exerted by the press. kla

A small hydraulic Press has input piston of radius 5 cm and output piston of radius 22 cm. The output piston is connected to a pressing plate of area 8.6 cm If the input force is F, =230 N, calculate the compressive Stress in ePa exerted by the press. kla

Name: A small hydraulic Press has input piston of radius5 cm and output pis
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: A small hydraulic Press has input piston of radius5 cm and output piston of radius 22 cm. Theoutput piston is connected to a pressing plate ofarea 8.66 cm ?. If the input force is F, =230 N,calculate the compressive Stress in RPa exerted bythe press

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 107AP: (a) Convert normal blood pressure readings of 120 over 80 mm Hg to newtons per meter squared using...

See similar textbooks

Similar questions

A sump pump (used to drain water from be basement of houses built below the water table) is draining a flooded basement at rate of 0.750 L/S, with an output pressure of 3.00105N/m2 . (a) The water enters a hose with a 3.00-cm inside diameter and rises 2.50 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.500 m in height and widens to 4.00 cm in diameter. What is the pressure now? You may neglect frictional losses both parts of the problem.
Verigy that the SI of hpg is N/m2.
What pressure is exerted the bottom of a gas tank that is 0.500-m wide and 0.900-m long and can hold 50.0 kg of gasoline full?
Calculate Reynolds numbers for flow of trough (a) a nozzle a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when be nozzle is attached to hose. The flow rate through hose and nozzle is 0.500 L/s. Can flow in either possibly be laminar?
A large tanker truck can carry 20 tons (40.000 lb) of liquid (a) What volume of water can it carry? (b) What volume of gasoline can it carry?
Suppose you have a coffee with a circular cross-section and vertical sides (uniform radius). What is its inside radius if it holds 375 g of coffee filled to a depth of 7.50 cm? Assume coffee has the same density as water.
Check Your Understanding Would a hydraulic press still operate properly if a gas is used instead of a liquid?
How would you determine the density of an irregularly shaped rock?
The pressure dam early in problems section increases with depth. Therefore, there is net torque on the dam. Find be net torque.
Using the equation of the previous problem, find the viscosity of motor oil in which a steel ball of radius 0.8 mm falls a terminal speed of 4.32 cm/s. The densities of the ball and the oil are 7.86 and 0.88 g/mL, respectively.
A frequency quoted rule of thumb aircraft design is that wings should produce about 1000 N of lift per square meter of wing. (The fact that a wing has a top and bottom surface does not double its area.) (a) At takeoff, an aircraft travels at 60.0 m/s, so that the air speed relative to the bottom of the wing is 60.0 m/s. Given be sea level density of air as 1.29kg/m3, how fast must it move over be upper surface to create the ideal lift? (b) How fast must air move over the upper surface at a cruising speed of 245 m/s and at an altitude where air density is one-fourth that at sea level? (Note that his not all of be aircraft's lift—some comes from be body of the plane, some from engine thrust, and so on. Furthermore, Bernoulli's principle gives approximate answer because flow over wing creates turbulence.)
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.