A lossless transmission line has a capacitance per unit length of 64pF/m and an inductance per unit length of 1µH/m. The load impedance ZL is purely resistive. Both the load impedance and the generator impedance are 50 Ohms. the reflection coefficient at the load, and the Voltage Standing Wave Ratio -0.429, -2.5 0.429, -2.5 -0.429, 2.5 -0.429, 3.5

A lossless transmission line has a capacitance per unit length of 64pF/m and an inductance per unit length of 1µH/m. The load impedance ZL is purely resistive. Both the load impedance and the generator impedance are 50 Ohms. the reflection coefficient at the load, and the Voltage Standing Wave Ratio -0.429, -2.5 0.429, -2.5 -0.429, 2.5 -0.429, 3.5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.32MCQ

See similar textbooks

Similar questions

Give example problems for impedances and admittance.
4/ Which parameter is neglected or ignored in Short Transmission Lines? A. SHUNT CAPACITANCE ONLY B. SERIES CONDUCTANCE AND SHUNT CAPACITANCE C. SHUNT CONDUCTANCE AND SHUNT CAPACITANCE D. SHUNT CONDUCTANCE ONLY
Each conductor of a 3-0 overhead line is suspended from a cross arm of a steel tower by a string of 4 suspension insulators. The voltage across the third 33 kV. The shunt capacitance between each insulator and the earth is 1/8th of the capacitance of the insulator itself. Find the voltage across string and string efficiency. D-128 Lod Fa
In the Transmission Line Simulator, the Transmission Line is composed of which parameter/s? O A. The Shunt Conductance Only O B. The Series Impedance and Shunt Capacitance O C. The Shunt Capacitance Only O D. The Series Impedance Only
IN rectangular waveguide, we know that in TM mode field, Ez (longitudinal field) is out f phase by 90 degree, why is it?
6-A lossless T.L. has Zo = 100 N and is loaded by an unknown impedance Its VSWR is 4 and the first voltage maximum is A/8 from the load . Find the load impedance .
2.5 A 3-phase single circuit bundled conductor line with two sub-conductors per phase has horizontal spacing with 6.1 m between the centre lines of adjacent phases. The distance between the sub- conductors of each phase is 30.5 cm and each sub-conductor has a diameter of 2.54 cm. Find the inductance per phase per km. [0.988 mH]
In the figure, a traveling voltage wave of 500 kV proceeds towards point A. Calculate the voltages and currents in the branches after the first reflection and transmission at point A.
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
Subject - Design electrical circuits for single-phase AC networks Question Discuss the difference between resonant and nonresonant circuits
A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight meter. Determine 1)The capacitance in uF/km without effect of ground 2)The capacitance in uF/km with effect of ground