a) In extreme cases, the filled bucket of water is dropped from rest (see the figure above). Help Ana and her community determine the velocity of the bucket upon hitting the surface of the water. b) When these extreme cases happen, we need to make sure the bucket is strong enough. What materials can be used for the water bucket? Are there special considerations since this will be deployed in rural communities?

a) In extreme cases, the filled bucket of water is dropped from rest (see the figure above). Help Ana and her community determine the velocity of the bucket upon hitting the surface of the water. b) When these extreme cases happen, we need to make sure the bucket is strong enough. What materials can be used for the water bucket? Are there special considerations since this will be deployed in rural communities?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.124P: The automobile, with center of gravity at G, is parked on an 18 slope with its brakes off. Determine...

See similar textbooks

Similar questions

The assembly shown consists of a flywheel, a counterweight, and a bolt that attaches the counterweight to the flywheel. The flywheel is uniform with mass per area of 3 g/mm² and has a 40 mm diameter hole as shown. Determine the mass mc of the counterweight so that the center of mass of the assembly is at point O. The counterweight is attached to the flywheel by a bolt with mass mp= 800 g that is screwed into a 10 mm diameter hole that passes completely through the flywheel. (Round the final answer to four decimal places.) flywheel 40 mm o counterweight and bolt mc, mB 45 mm 100 mm 50 mm The mass mc of the counterweight is g.
Find the center of mass of the system shown if M1= 10 kg, and M2= 20 kg. Mr M: 3. 2.
The figure shows composite shape comprising of two long slender rod bodies. The horizontal body has a length of 1.2m and mass 3kg; the second body has a length 0.4m and mass 1kg. The centre of gravity of each of the individual bodies can be found at their geometric centre, labelled G₁ and G2₂ in the figure. The composite shape has symmetry about the x axis, thus its centre of gravity lies on the line 'y=0' as depicted in the figure. Calculate the x coordinate of the centre of gravity of the composite shape. O O 0.95 m 0.75 m 0.50 m Don't Know 0.60 m G₁ G₂
A truck is driving over a scale at a weight station. When the front wheels drive over the scale, the scale reads 5800 N. When the rear wheels drive over the scale, it reads 6500 N. The distance between the front and rear wheels is 3.20 m Determine the distance between the front wheels and the truck's center of gravity.
If the cylinder mass is 83 kg, determine the cylinder A mass to hold the system in the figure position.
Compute its initial metacentric height and determine whether the body is stable or not.
5-10 Three bodies with masses of 3, 6, and 7 kg are lo- cated at points (4, -3, 1), (-1, 3, 2), and (2, 2, -4), respec- tively. Locate the mass center of the system if the distances are measured in meters.
The plant in the picture has mass of 29 kg, and is hanging at a distance of 1.4 meters from the wall. The horizontal rod has mass of 6.2 kg. Assume that its weight is evenly distributed, therefore it can be treated as a single force at the center of mass. The rod is 2 meters long, and there is a cable at a 23° angle supporting it at the end. Center of mass of rod from the point = 2/2=1m Using the wall as the axis of rotation, find the magnitude of the downward torque, from both the weight of the rod and the weight of the plant. t=458.64Nm a.The downward torque is balanced by the upward torque from the force of tension. Find the magnitude of the force of tension. T=?N b.F is the contact force between the rod and the wall. Using the other horizontal force in the problem, find the horizontal component of F (the normal force) that must be present for the rod to be at equilibrium. Fx=?N c.There is a vertical force from a component of the tension, but this is not enough to balance the…
Q/ Determine the equivalent mass of the system in the direction of x Slender rod of mass m 2m ITTM
The 2000 kg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC. The diameters of AB and AC are 12 mm and 10 mm, respectively. Determine the weight of the concrete pipe ( in N).
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
13 см Vaxn's 29cm 26cm !- Stancs X ax. 5. Find The location of conter of gravity