A heat engine experiment was done using a cold reservoir at 10°C and a hot reservoir at 80°C. The resulting P-V diagram for the experiment is shown below. Which of the following shows an isothermic expansion process? Heat Engine Cycle 104500 B 104000 103500 103000 Area = 0.05625 102500 102000 101500 A D 101000 1.70E-04 1.80E-04 1.90E-04 2.00E-04 2.10E-04 2.20E-04 Volume (m³) Pressure (Pa)

A heat engine experiment was done using a cold reservoir at 10°C and a hot reservoir at 80°C. The resulting P-V diagram for the experiment is shown below. Which of the following shows an isothermic expansion process? Heat Engine Cycle 104500 B 104000 103500 103000 Area = 0.05625 102500 102000 101500 A D 101000 1.70E-04 1.80E-04 1.90E-04 2.00E-04 2.10E-04 2.20E-04 Volume (m³) Pressure (Pa)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

During the time 0.325 mol of an ideal gas undergoes an isothermal compression at 22.0∘C, 392 J of work is done on it by the surroundings. If the final pressure is 1.76 atm, what was the initial pressure? What is the pV-diagram for the process?
from the pint uwe the PV diagram of the Qvestion: Name the three prolesses. three processes, Р (Рa) B T2 V (m³) a) what ty pe of process A D what ty pe of process c) What ty pe of process A รพer Iso ther mal process Adjabatic process I sovolumetric process I so baric process Cy clic process Iso choric process
The pV diagram in (Figure 1) shows a process abc involving 0.550 mol of an ideal gas. For related problem-solving tips and strategies, you may want to view a Video Tutor Solution of A cyclic process. Figure 8.0 6.0 4.0 2.0 p(Pax 105) 0.020 0.040 0.060 b 0.080 1 of 1 -V(m³) What was the temperature of this gas at points a, b, and c? Enter your answers separated by commas. LIVE ΑΣΦ Tas To Tc 937.7,7654.12, 12296.59 Submit X Incorrect; Try Again; 3 attempts remaining Part B Previous Answers Request Answer How much work was done by or on the gas in this process? Express your answer in joules. W = 2.1×104 J Submit Previous Answers Part C Correct The work done in a process is the area under the curve in the pV diagram. The work done by the gas is positive since the volume increases. The magnitude of the work is the area under the curve: W = (2.0 × 105 Pa + 5.0 × 105 Pa)(0.070 m³ – 0.010 m³) = 2.10 × 10¹ J VO How much heat had to be put in during the process to increase the internal energy of…
The figure (Figure 1)shows the cycle for a heat engine that uses a gas having y = 1.25. The initial temperature is T1= 300 K, and this engine operates at 16 cycles per second.
The fpicture shows a pV diagram for an ideal gas in which its pressure tripled from a to b when 804 J of heat was put into the gas. a) How much work was done on or by the gas between aa and bb? Express your answer in joules. b) Fill in the sentence, do they increase, decrease, or stay the same. " The temperature of this gas ______ between a and b. When pressure increases, the temperature _____ provided that V and n are _______." c) By how much did the internal energy of the gas change between a and b? Express your answer in joules. Did it increase or decrease? d) What is the temperature of the gas at point b in terms of its temperature at a, Ta
A steam turbine receives a steam flow rate of 2kg/s and the power output is.. 700 kW. The heat loss from the casing is negligible. B. when the velocity at the entrance is 60 m/s, the velocity at exit is 360 m/s, and the inlet pipe is 3 m above * ?the exhaust pipe, the change of specific enthalpy across the turbine is 700 600 400 NON OF THE ABOVE
A sample containing 1.0 mole of oxygen gas initially at 45 degrees Celsius is heated to 110 degrees Celsius under isobaric conditions. From these given data, answer the questions that follows. What is the sample's change in internal energy (in KiloJoules)? What is the sample's change in enthalpy (in KiloJoules)?
For the heat pump (used for heating) illustrated below, what is its coefficient of performance for heating. Ag? The gas is monatomic. p(Pa) 6 A. 8/3 B. 2 C. 11/3 D. 14/3 E. 19/7 2 V(m³) 34
Air goes through a Brayton cycle gas turbine, entering the compressor at 11 °C and 92 kPa. When it reaches the turbine inlet, the air is at 807°C and 1.20 MPa. What is the net change in specific enthalpy of the working fluid after going through the compressor and heat addition processes? You may assume that the specific heat capacity G, is a constant 1.005 kJ-kg1-K1 throughout the whole cycle. Gjve your answer in kJ-kg to one decimal place.
Consider the thermodynamic process, A->B->C->A shown above. The heat absorbed during A->B is 591J. If the change in internal energy during B->C is 4146J, What is the change in internal energy in SI units during C->A? Express only the number of your answer with 4 significant figures.
Converting sunlight to electricity with solar cells has an efficiency of 15%. It's possible to achieve a higher efficiency (though currently at higher cost) by using concentrated sunlight as the hot reservoir of a heat engine. Each dish in (Figure 1) concentrates sunlight on one side of a heat engine, producing a hot-reservoir temperature of 560 ∘C. The cold reservoir, ambient air, is approximately 30 ∘C. The actual working efficiency of this device is 30%. What is the theoretical maximum efficiency?
1.50 mol of an ideal gas with a constant ratio of heat capacities at constant pressure and volume y =2 = 1.40 is taken through the (reversible) cycle shown in the figure below. The process A - B is an expansion at constant temperature, whereas B →C and C → A are constant-pressure compression and constant-volume processes, respectively. 040 a) What is the temperature TA of the gas at A? P (atm) For the cycle as a whole, Isothermal b) calculate the (net) work done W (by the gas), 04021 c) calculate the (total) heat transfer Q, process d) find the change in the (internal) energy U of the gas, B e) verify that the 1" law of thermodynamics C is satisfied. 1 liter=1.00x10 m , 1 atm=1.01x105 N/m² , kɛ = 1.38x1023 J/K , NA=6.02x1023 mol. -V (liters) 50 10