A double riveted single cover butt joint (zig zag arrangement), is used for connecting twoplates 15mm thick. The diameter of the rivets is 20mm and the pitch is 100mm. Draw thejoint with hand sketch and calculate the efficiency of the joint, if permissible stresses are asbelow:Permissible shearing stress in rivets = 120MpaPermissible tensile stress in plate = 150MPaPermissible crushing stress in rivets = 210MPa

Given:- Permissible shearing stress in rivets = 120 MPa- Permissible tensile stress in plate = 150…

Answered: A double riveted single cover butt…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A double riveted lap joint is made between 15mm thick plates. The rivet diameter and pitch are 25 mm and 75 mm, respectively. If the ultimate stresses are 400 MPa in tension, 320 MPa in shear and 640 MPa in crushing, find the minimum force per pitch which will rupture the joint. If the above joint is subjected to a load such that the factor of safety is 4, find out the actual stresses developed in the plates and rivets.
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
Design a single riveted lap joint to connect two mild steel plates, 14.5 mm thick, the joint being designed for maximum efficiency. The allowable stresses are σt = 55 N/mm2 , = 32.5 N/mm2 and σc = 63.5 N/mm2 . Also calculate the minimum force per pitch which will rupture the joint
Two plates 20 mm thickness are fastened by a number of 25 mm diameter rivets, a tensile load of 500 KN was applied, find the number of rivets required if the shearing stress is limited by 70 MPa and the bearing ?stress of plates is limited by 105 MPa
Calculate the riveted joints, find its efficiency and draw a suitable sketch. Thickness of the plates – t, mm is 12 Width of the plates – b, mm is 150 Load – P, kN is 20 Note. Choose a suitable material, determine its tearing stress. Take permissible shearing stress - teta=0.7sigmat ; Permissible crushing stress - sigmac=1.5sigmat ;
Solve the following problem of a steel tensile plate with a concentrated load applied at the top, as shown below. Determine at what depth the effect of the load dies out. Plot stress oy versus distance from the load. At distances of 1 in., 2 in., 4 in., 6 in., 10 in., 15 in., 20 in., and 30 in. from the load, list oy versus these distances. Let the width of the plate be b = 4 in., thickness of the plate be t = 0.25 in., and length be in. Look up the concept of St. Venant's principle to see how it explains the stress behavior in this problem. L P = 1000 lb NUMI - E бу bt Oy bt 6 Gy = = P bt
2. A 30-mm bolt with an initial tension of 35 kN is subjected to several types of stresses during initial tightening or due to screwing up forces. If the bolt has a core diameter of 25.7 mm and considering 5 threads are already engaged with the nut, calculate the shear stress across the thread and the crushing stress between the threads. Assume 3.5 mm as the width of the thread section at the root.
A plate 70mm wide and 15mm thick is joined with another plate by a single transverse weld and a double parallel fillet weld. The maximum tensile and shear stresses are 60MPa and 50MPa respectively. Find the length of each parallel fillet weld, if the joint is subjected to static loading.
A square pedestal has glued parts at joints t, r, e, and s. Plane t-r-e-s is at anole of 30° from the vertical axis Given the following data: allowable pressive stress of 5.2 MPa in glued joint and Shear stress of 3.5 MPa. If the axial pedestal force is 36 kN. determine the safe width dimension in mm and the angle in degrees if the maximum shear stress will occur to the plane.
c) A cylinder with external diameter 280mm and internal diameter 200mm is subjected to an internal pressure of 30 MPa. Compare the relative merits of a single thick walled cylinder and a composite cylinder with the inner cylinder whose internal and external diameters are 200mm and 250 mm respectively. A tube of 250 mm internal diameter and 280mm external diameter is shrunk on the main cylinder. The safe tensile yield stress of the material is 110 MPa and the stress set up at the junction due to shrinkage should not exceed 10 MPa.
Design a Knuckle joint to transmit122 kN. Allowable stresses in tension, shear and compression are 75 N/mm2 in tension, 65 N/mm2 and 140 N/mm2 respectively
3. Problem 2: The lap joint is fastened with four rivets. If the working stress is 14 ksi (kips per square inch) for the rivets in shear, find the diameter (in inches) of the rivets that maybe installed to the joint. Assume that the load is equally distributed among the rivets. P= 15 kips. P. 4 in. in. 000 Your answer 4. In Problem 2, if the working stress is 18 ksi for the plates in bearing, find the diameter (in inches) of the rivets that maybe installed to the joint. Assume that the load is equally distributed among the rivets. Your answer 5. In Problem 2, what is the diameter (in inches) of the rivets that can be installed to the joint. Your answer

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS