A compressed air vessel has an inside diameter of 2 m and a plate thickness of 12,5 mm. If the tensile stress induced in the plating is to be limited to 100 MPa, calculate for both the longitudinal and circumferential seams the pressure necessary to induce this stress. Take the longitudinal and circumferential joint 85% and efficiencies as 70% respectively. What would the actual allowable pressure be?

A compressed air vessel has an inside diameter of 2 m and a plate thickness of 12,5 mm. If the tensile stress induced in the plating is to be limited to 100 MPa, calculate for both the longitudinal and circumferential seams the pressure necessary to induce this stress. Take the longitudinal and circumferential joint 85% and efficiencies as 70% respectively. What would the actual allowable pressure be?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2: An otl of viscosity Co.15 pas) and specific gravity 0.9 is flows Throngh 1.Find The slope of The Pipe That will canse The Pressure to be constantalong The pipes entire length? an inclined (300mm) diameter Pipe. Q= 0.005m3/sec 3oomm Dia. Zz datum 2. check if The Rlow is laminarRlow?
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate ftop at the ends. (MPa), consider sign convention (- for compression, + for tension) Š KN/m EXCLUD In6 SELFWEI6HT 300 = P P = 300 kN 15M オ 400 Ye = 24 1N m3 N.A. 800 70
A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the stress in a fiber 50mm from the top of the beam at point B. 50kN A 20 купи RI B 2M X 30KN/M TITT. 4m 20 km. ITTJ 2m + <
Q1: Shaft subjected to the loadings in phase shown such that: T=0 N.m to 200 N.m M=-200 to 200 N.m The shaft has d1=60 mm, d2=40mm, r=8 mm, cold drawn, operating temp. 550 C, relaibility of the data 99.9%, Material Properties; out = 1260 MPa, Out=813 Mpa. Is the shaft fails for infinity life design? T. M di d
momentum.pdf 9/1 The se extra examples are presented by Mohammed Dheyaa 2021© H.W.l Giuen V, = 25m/s S.g.= 0.83 Find the force requited F-マ。 plate d=somm v, = 36m/s negkcting frichion betu
Q1. Find: (a) the stress in the Steel and Aluminium rods after the loap P applied and the temprature raised 60 C° and (b) the displacement under the load P. Using the data in the Table below. (30 Mark) Rod A (mm') a (µm/m. Cº) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 11.2 190 44 Aluminium 350 18.9 35 85 Aluminium A Steel 4m d + 2m P
A 300 mm X 500 mm reinforced concrete edge beam is monolithically casted to a 100 mm slab. The beam is an interior beam reinforced with 5 – Ø25 mm bars for tension and 010 mm bars for stirrups. If a Ø120 mm and a Ø80 mm pipe pass through the beam's cross-section, the center of the pipes are located 90 mm and 115 mm, respectively from the top of the flange. Determine the following using an f'c = 25 MPa and fy = 415 MPa: Use NSCP 2015 to layout the reinforcement of this beam. The overhanging flange width, if the depth of compression block is just enough to include the two pipes. a. i. ii. Ultimate Moment Capacity of the Beam ii. Balanced Steel Ratio iv. Centroid of the Beam's Cross Section neglecting the reinforcement.
Oil sg = 0.84 flowing through a pipe %3D has a total heal loss 3ft from pt.1 to pt.2. As the figure is shown, find the pressure (in pound/ squarefeet) at pt.2. Point 1 D, -6 -65 Q- 2.08 da 10.20 Q-2.06 ch Point 2 D,-9m 2-7 4.00 Reference datum Pig. 8-25
Determine the viscosity of fluid between shaft e 2 - sleeve shown in fiqure below Assump linear velocity distri bution. 200mum fluid Aus. : 1.183 pa.s V=o.12 89N A> const. velaity 7 Sum dia
Water flows through a 600 mm diameter pipe with a velocity of 2.7 m/s. Bulk modulus of water is 2060 MPa and the pipe has modulus of elasticity of 200 GPa. The pipe has thickness of 18 mm. Determine the length of the pipe subject to peak closure.
Handliston A steel penstock 500 mm in diameter has shell thickness of 10 mm. The modulus of elasticity of the shell material is 2.0 x 105 N/mm2 & the bulk modulus of elasticity of water is 2.0 x 103 N/mm2. The pipe is designed to discharge water at a mean velocity of 2.0 m/sec. Determine the pressure rise caused by the sudden closure of a valve at the downstream end by neglecting the elasticity of the pipe material.
W₁=2,5*/F5 W₁ = 2 * /FT + 201 ㅓ - R=2K 14 2#9 18' ·5#9 I3¹ 121 15 367 $3 A.) Calculate the instanteous deflection and the long --term id Election after 4 years. Assume the dead load includes the beam weight and load sustained. Assume n = 8 +y = 60000 gs i fi = 4000 psi Assume the beam weight is included in dead load and normal weight concrete is used. b.) is the beam satisfactory beam that does not support any elements likely to be damaged by large deflections ? a flat roof nonstructura as love 20% of 20Ve