A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given Es= 2 x 105 N/mm and Ec= 1.2 x 105 N/mm2

A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given Es= 2 x 105 N/mm and Ec= 1.2 x 105 N/mm2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.1P: A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends....

See similar textbooks

Similar questions

The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
An element of aluminum is subjected to tri- axial stresses. Calculate the strains in the element in and directions if the stresses are -20 MPa, 28 MPa, and -18 MPa. respectively. Assume E = 70 GPa and v = 0.33. Also, find the strain energy density of the element.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A circular post, a rectangular post, and a post of cruciform cross section are each compressed by loads that produce a resultant force P acting at the edge of the cross section (see figure). The diameter of the circular post and the depths of the rectangular and cruciform posts are the same. For what width b of the rectangular post will the maximum tensile stresses be the same in the circular and rectangular posts? Repeat part (a) for the post with cruciform cross section. Under the conditions described in parts (a) and (b), which post has the largest compressive stress?
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A circular aluminum tube of length L = 600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d2= 75 mm and d1= 63 mm, respectively. A strain gage is placed on the outside of the lube to measure normal strains in the longitudinal direction. Assume that E = 73 GPa and Poissons ratio is v = 0.33. (a) IF the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e = 78 J X 10-6, what is the shortening
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
Plastic bar of diameter d = 32 mm is compressed in a testing device by a Force P = 190 N that is applied as shown in the figure. (a) Determine the normal and shear stresses acting: on all faces of stress elements oriented at (1 ) an angle 8 = 00, (2) an angle ?? = 22.5s, and (3) an angle ?? = 45°. In each case, show the stresses on a sketch of a properly oriented element. What are smaxtmax (b) Find smax and tmax in the plastic bar if a re-cantering spring of stiffness k is inserted into the testing device, as shown in the figure. The spring stillness is 1/6 of the axial stiffness of the plastic bar.
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates