a C: The switch in the circuit above has been in position a for a long time. The variables in the figure are as follows: AV = 10 volts, C = 3 µF, R = 24 Q. It is changed to position b at t = 6 us. What are the Q on the capacitor and the current I through the resistor (a) immediately after the switch is closed? (b) at t =50 µs? and (c) at t= 220 µs? (d) ww

a C: The switch in the circuit above has been in position a for a long time. The variables in the figure are as follows: AV = 10 volts, C = 3 µF, R = 24 Q. It is changed to position b at t = 6 us. What are the Q on the capacitor and the current I through the resistor (a) immediately after the switch is closed? (b) at t =50 µs? and (c) at t= 220 µs? (d) ww

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 2PA: You are working in an industrial plant. You have been instructed to double the capacitance connected...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
EXAMPLE + 5V – 0.1uF At the instant the switch makes a contact with terminal a, the voltage across the capacitor is 5V. The 10V b 6V 100k2 switch remains at a for 9 ms then moves to terminal b. How many milliseconds after making contact with terminal a does the opamp 8V -6V saturate?
The circuit in the figure below contains two resistors, R1 = 4.00kΩ and R2 = 5.00kΩ, and two capacitors, C1 = 4.00uF and C2 = 5.00uF, connected to a battery with emf E = 120V. If no charges exist on the capacitors before switch S is closed, determine the charge q1 on capacitor C1 1.00ms after the switch is closed. Determine the charge q2 on capacitor C2 1.00ms after the switch is closed.
C) A 25 A electrodynamic ammeter is controlled by a spring having a constant of 5.7295x 10-6 Nm/rad. The full scale deflection is 110°. Determine the inductance of the instrument while measuring a current of 20 A. The mutual inductance at 0° deflection is 4 u H and the change in mutual inductance is linear with the deflection.
The magnitude of the voltage applied to the electrodes of a welding machine can be adjusted in the circuit below. In the range of minimum and maximum value that variable value resistor can take What is the time interval that the capacitor will charge from 0 to 8 V?
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
2:50 1 LTE O Motor Warning Light Instructions PHYS&110-VHY-S21-PHYSNON-SCIMAJORSWLAB-.. STEP 3 Now add a red LED (D1 in the main schematic) in series with 500N of resistance (shown as R1 in the main schematic). How you choose to arrive at 5002 is up to you. SW1 PSB D2 D3 1N4007 5 V D1 Blue Red R3 10 ka R1 500 Q • What happens now when SW1 is (and the PSB is turned on)? • What happens if you turn the diode at D3 around? (Don't forget to turn it back the right way afterward.) • Why does this circuit use a diode at D3 instead of a pull-up resistor? (Meaning, what would happen if a resistor were used instead of the diode?) pressed ( Previous Next 14 Dashboard Calendar To Do Notifications Inbox
1. Which of the following answers best describes discontinuous conduction mode? A. The inductor voltage ripple goes negative B. The inductor current ripple stays positive C. The inductor current ripple falls to zero D. The output current ripple falls to zero
Calculate the voltage at 1.5¹ (milliseconds) for the following RC Circuit. Assume switch is closed and capacitor is in a charge state. t=0 LE -10 V oto R1 1kQ C1 1uF
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?