A block of wood is tested in direct shear using the loading frame and test specimen shown in the figure. The load P produces shear in the specimen along plane AB. The height “h” of plane AB is 50 mm and its width (perpendicular to the plane of drawing) is 100 mm. If the load P = 16 kN, what is the average shear stress in the wood? Express the answer in MPa. A block of wood is tested in direct shear using the loading frame and test specimenshown in the figure. The load P produces shear in the specimen along plane AB. Theheight "h" of plane AB is 50 mm and its width (perpendicular to the plane of drawing)is 100 mm. If the load P = 16 kN, what is the average shear stress in the wood?Express the answer in MPa.ABSide Viewh

Given: Load→P=16 KN Height of the plane AB: →h=50 mm And width perpendicular to the plane: →w=100 mm…

A block of wood is tested in direct shear using the loading frame and test specimen shown in the figure. The load P produces shear in the specimen along plane AB. The height "h" of plane AB is 50 mm and its width (perpendicular to the plane of drawing) is 100 mm. If the load P = 16 kN, what is the average shear stress in the wood? Express the answer in MPa. Side View h

A block of wood is tested in direct shear using the loading frame and test specimen shown in the figure. The load P produces shear in the specimen along plane AB. The height "h" of plane AB is 50 mm and its width (perpendicular to the plane of drawing) is 100 mm. If the load P = 16 kN, what is the average shear stress in the wood? Express the answer in MPa. Side View h

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.12P: A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole...

See similar textbooks

Similar questions

A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A block of wood is tested in direct shear using the loading frame and test specimen shown in the figure. The load P produces shear in the specimen along plane AB. The height “h” of plane AB is 50 mm and its width (perpendicular to the plane of drawing) is 100 mm. If the load P = 16 kN, what is the average shear stress in the wood? Express the answer in MPa. why some answers are 6.40mpa and others are 3.2mpa? im confused
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
Q4) In fatigue test, the specimen constructed as in figure, which its broken at 50118 revolution. Calculating the maximum bending stress in Mpa applied to the specimen at a diameter 5 mm. L=125.2 mm K diameter = 5 mm 29.4 N
The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear stress in the 1.25 in. diameter axle?
A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube is r1 = 45 mm and the measured angle of twist betweenthe ends is 0.5°, what is the shear strain γ1 (in radians) at the inners surface? b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to bekept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius(r2)max?
The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of the block is 1cm. A shearing force applied to the top face produces a displacement of 0.015mm. Find the strain, stress and shearing force. Modulus of rigidity 4.5 x 10¹0 N/m². **Need asap pls. Thank you.
The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of the block is 1cm. A shearing force applied to the top face produces a displacement of 0.015mm. Find the strain, stress and shearing force. Modulus of rigidity 4.5 x 10¹0 N/m².
A block 100 mm x 100 mm base and 10 mm height. When we apply a tangential force 10 kN to the upper edge it is displaced 1 mm relative to lower face. Find the shear stress? and shear strain? *
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Qmoves to the left by u = 1.5 mm and upward by v = 3.0 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 680 mm, a = 29°, and 3 = 61% Answer: y = U i P a urad
Construct the shear-force diagram and identify the largest negative shear force. Assume a = 5.9 ft, b = 11.8 ft, c = 23.6 ft, w = 1180 %3D Ib/ft, and P = 3400 lb. B C D a b Answer: V min i Ib
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.2 mm and upward by v = 4.3 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 660 mm, a = 24°, and ß = 66% Answer: y= a R urad