A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced delta connected load. For the system, additional information are as follows: Vbc = 443 cis 191 degrees volts; and Ic = 10.5 cis99 degrees amperes What is the value of the total real power of the delta load in watts? ANSWER QUICKLY NO DIAGRM NEEDED

A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced delta connected load. For the system, additional information are as follows: Vbc = 443 cis 191 degrees volts; and Ic = 10.5 cis99 degrees amperes What is the value of the total real power of the delta load in watts? ANSWER QUICKLY NO DIAGRM NEEDED

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23MCQ: In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the...

See similar textbooks

Similar questions

What is the total real power and total reactive power consumed by the three-phase load (regardless if wye or delta)?
Two reverse parallel scr are used to control the voltage on a 10 ohm load over a 230V, 50HZ 1- phase AC source, and triggering is done at 3O degrees for positive alterance. Calculate the effective (rms) voltage on the load. a) 230.34V b) 226.64V c) 220V d) 110.56V e) OV
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
Propose size of the capacitor required to improve the pf of a single phase system to 98%. The system supplies follwoing loads i) Lighting load of 50 kW p.f=1 ii) Induction motor load of 125 kW with a lagging p.f of 0.707 iii) A synchronous condenser of 75 kW at p.f 0.9 iv) Other miscellaneous loads of 25 kw at p.f 0.8 lagging. The voltage of the system is xxx V where xxx is 311
a) why is there a wattmeter reading when the load is purely inductiveb) why is there no wattmeter reading when the load is purely capacitive
The Circuit diagram for a power system is shown in Figure Q2. A synchronous generator consists of voltage source, in rms, (Van = 110 20° V, Van = 110 2-120° V and Ven = 110 -240° V). The transmission line has an impedance (Zine) of 0.05 + j0.10 O per phase, and the load has an impedance (Z.) of 12 + j6 0 per phase. line Von line Z, V. cn bn В lin Figure Q2 a. As an electrical engineer, explain about the power system in Figure Q2 with respect to the voltages, and the connection for the source and the load. Give at least FOUR (4) points. b. Solve the followings: i. the line currents. ii. the real, reactive and apparent powers consumed by the load per phase.
A three-phase alternator generating unbalanced voltages is connected to an unbalanced load through a 3-phase transmission line as shown in figure. The neutral of the alternator and the star point of the load are solidly grounded. The phase voltages of the alternator are Ea = 1020°, Eb = 102-90°, Ec = 10/120⁰ E E E The positive sequence component of the load current is (A) 1.3102-107⁰ A (B) 0.332Z –120° A (C) 0.9962-120° A (D) 3.5104-81⁰ A +) + j1.002 0000 j1.002 0000 j1.0Ω vovo j1.0Ω 0000 j2.002 voor j3.002 oooo
The figure shows a 3-phase bala Time left 1:06:30 200 /00 Vrms. sequence electrical system. Vcn Vbn %3D al Balanced (-) sequence 100 so a 2000 Vms Select one: O a. 200 /-120 Vrms O b. 200 v2 /0 Vrms O C. 200 /0 Vrms O d. 200 v2/-120 Vrms e. 200/120 Vrms
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Does an open connection permit balanced three-phase operation? - (a) Yes (b) No