A 50 ksi W14x22 is used as a compression member. The member is pinned at each end and it 8-feet long. Please determine the design strength of the compression member (LRFD). Hint: Local buckling will govern, so local buckling must be checked and the effective area (Ae) must be calculated to determine the nominal compressive strength (Pn)

A 50 ksi W14x22 is used as a compression member. The member is pinned at each end and it 8-feet long. Please determine the design strength of the compression member (LRFD). Hint: Local buckling will govern, so local buckling must be checked and the effective area (Ae) must be calculated to determine the nominal compressive strength (Pn)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.4.2P

See similar textbooks

Similar questions

Question 1: (Use NSCP 505.3 provisions and ASEP Steel Handbook for effective length factors) Use AISC Equation E3-2 or E3-3 and determine the nominal axial compressive strength for the following cases: a. L= 15 ft b. L=20 ft W10 × 33 A992 steel FIGURE P4.3-1
Use 2015 NSCP. A compression member shown below with Fy = 50 ksi 30′ W12 x 87 A992 steel 1. Which of the following most nearly gives the value of critical buckling stress in ksi? 2. Which of the following most nearly gives the nominal strength in kips? 3. Considering ASD. Which of the following most nearly gives the allowable strength in kips? 4. Considering LRFD. Which of the following most nearly gives the design strength in kips?
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
For the column shown what is the nominal compressive strength (Pn) ? Pn=? W12x50 10 12X50 THT X combilevered WI
A flexural member is fabricated from two flanges plates 1/2" x 18" and a web plate 5/16" x 20". The yield stress of the steel is 36 ksi. a. Compute the elastic modulus and the yield moment with respect to major principal axis. b. Compute the plastic modulus and the plastic moment with respect to major principal axis.
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1
4.3-4 Determine the available strength of the compression member shown in Figure P4.3-4. in each of the following ways: a. Use AISC Equation E3-2 or E3-3. Compute both the design strength for LRFD and the allowable strength for ASD. 15 HSS 10x6x ASTM A500, Grade B steel (Fy=46 ksi) 2/3
A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H FO E. • D A В
Estimate the cross-sectional area of a 350S125-27 cold-formed shape. a. If the member is tested in tension, what would be the maximum force thesample could carry before reaching the yield strength if the steel has ayield strength of 225 MPa?b. Would you expect a 2.5 m stud to carry the same load in compression?(explain)
AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
The wall bracket show below carries a load of P Kip. the allowable tensile in the eye bar is 20 ksi, and the allowable shear stress in the pin is 12 ksi. Select: a) The diameter of the eye bard b) the diameter of the pin at A which is double shear c) the diameter of the pin at B which is single One eye-bar 6 ft P kip 4 ft