A 5.2-kg bowling ball is attached to a weightless rod with dimensions shown below. The other end is attached to a rusty hinge so that it can swing like a pendulum. The ball is released when the rod is horizontal and the ball swings down and then up to a certain angle on the other side. During the swing, the rusty hinge steals 80% of the ball's initial potential energy. Find the maximum angle 0 of the rod from the vertical. SO -2.30 m-

A 5.2-kg bowling ball is attached to a weightless rod with dimensions shown below. The other end is attached to a rusty hinge so that it can swing like a pendulum. The ball is released when the rod is horizontal and the ball swings down and then up to a certain angle on the other side. During the swing, the rusty hinge steals 80% of the ball's initial potential energy. Find the maximum angle 0 of the rod from the vertical. SO -2.30 m-

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter7: Conservation Of Energy

Section: Chapter Questions

Problem 45P: A small block of mass m = 200 g is released from rest at point along the horizontal diameter on the...

See similar textbooks

Similar questions

A small particle of mass m is pulled to the top of a friction less half-cylinder (of radius R) by a light cord that passes over the top of the cylinder as illustrated in Figure P7.15. (a) Assuming the particle moves at a constant speed, show that F = mg cos . Note: If the particle moves at constant speed, the component of its acceleration tangent to the cylinder must be zero at all times. (b) By directly integrating W=Fdr, find the work done in moving the particle at constant speed from the bottom to the top of the hall-cylinder. Figure P7.15
To develop muscle tone, a woman lifts a 2.00-kg weight held in her hand. She uses her biceps muscle to flex the lower arm through an angle of 60.0°. (a) What is the angular acceleration if the weight is 24.0 cm from the elbow joint, her forearm has a moment of inertia of 0.250kg-m2 and the net force she exerts is 750 N at an effective perpendicular lever arm of 2.00 cm? (b) How much work does she do?
A small block of mass m = 200 g is released from rest at point along the horizontal diameter on the inside of a frictionless, hemispherical bowl of radius R = 30.0 cm (Fig. P7.45). Calculate (a) the gravitational potential energy of the block-Earth system when the block is at point relative to point . (b) the kinetic energy of the block at point , (c) its speed at point , and (d) its kinetic energy and the potential energy when the block is at point . Figure P7.45 Problems 45 and 46.
A block is connected to a spring that is suspended from the ceiling. Assuming air resistance is ignored, describe the energy transformations that occur within die system consisting of the block, the Earth, and the spring when the block is set into vertical motion.
The figure shows a rigid assembly of a thin hoop (of mass m = 0.30 kg and radius R = 0.17 m) and a thin radial rod (of length L = 2R and also of mass m = 0.30 kg). The assembly is upright, but we nudge it so that it rotates around a horizontal axis in the plane of the rod and %3D %3D hoop, through the lower end of the rod. Assuming that the energy given to the assembly in the nudge is negligible, what is the assembly's angular speed about the rotation axis when it passes through the upside-down (inverted) orientation? Hoop Rod Rotation axis Number 9.23 Units rad/s
Computation. The figure shows two blocks, released from rest, connected by a light string passing without slipping over a pulley with moment of inertia 0.032 kg-m² and radius 0.1 m. The coefficient of kinetic friction between the block and the table is 0.38. Using energy methods, find the blocks' speed after they have moved 0.22 m if M = 5.2 kg and m = 7.3 kg. V= M 11 m/s m Record your numerical answer below, assuming three significant figures. Remember to include a as necessary. 31 6:37 P
A smooth circular hoop with a radius of 0.900 m is placed flat on the floor. A 0.475-kg particle slides around the inside edge of the hoop. The particle is given an initial speed of 9.00 m/s. After one revolution, its speed has dropped to 5.00 m/s because of friction with the floor. (a) Find the energy transformed from mechanical to internal in the particle-hoop-floor system as a result of friction in one revolution. 13.3 (b) What is the total number of revolutions the particle makes before stopping? Assume the friction force remains constant during the entire motion. 1 Your response differs from the correct answer by more than 10%. Double check your calculations. rev
a rigid assembly of a thin hoop (of mass mand radius R = 0.150 m) and a thin radial rod (of mass m and length L = 2.00R). The assembly is upright, but if we give it a slight nudge, it will rotate around a horizontal axis in the plane of the rod and hoop, through the lower end of the rod. Assuming that the energy given to the assembly in such a nudge is negligible, what would be the assembly’s angular speed about the rotation axis when it passes through the upside-down (inverted) orientation?
A 10.0-kg bob is attached to a rod whose length is 10.0 m. The right end of the rod is fixed, and the bob is released from rest. a) Determine the speed of the bob when it is below the pivot point (vertical angle is zero). b) Determine the tension in the rod when the bob is below the pivot point. hint: to determine the speed of the bob when it is below the pivot point, you will need to use Calculus.
A 31 kg skip attached to a steel rope on a crane is used to hoist bricks from the ground to the top of a construction site. The steel rope is wound onto a lifting drum with a diameter of 700 mm and rotational frequency of 80 revolutions per minute. The lifting drum is situated on the top floor which is 195 m high. Calculate the total work done (in joules) to lift the 20 bricks(150 Kg) from the bottom to the top of the building.
a rigid assembly of a thin hoop (of mass m = 0.25 kg and radius R = 0.19 m) and a thin radial rod (of length L = 2R and also of mass m = 0.25 kg). The assembly is upright, but we nudge it so that it rotates around a horizontal axis in the plane of the rod and hoop, through the lower end of the rod. Assuming that the energy given to the assembly in the nudge is negligible, what is the assembly's angular speed about the rotation axis when it passes through the upside-down (inverted) orientation?
Malar is playing with a toy car track set and has made a vetical loop she wants to send a 150-gram car around. She has a hill for the car to roll down and if she releases it from a height of 24 cm above the top of the loop, which has a radius of 20 cm, it goes around the loop and exits with a speed of 3.12 m/s. How much energy was lost due to friction (between the car and the sides of the track, and the car's axels) during the entire trip? Hint: You don't have any details about the time while the car is going down the hill or through the loop, so you don't know how fast it is going at the top of the loop.