A 480V/240V, 60Hz single transformer has Z1 = 0.1+j0.22 ohms and Z2 = 0.035 + j0.12 ohm. Find the equivalent impedance in ohm referred to the secondary. Group of answer choices 0.07+j0.135 0.06+j0.175 0.04+j0.135 0.06+j0.135

A 480V/240V, 60Hz single transformer has Z1 = 0.1+j0.22 ohms and Z2 = 0.035 + j0.12 ohm. Find the equivalent impedance in ohm referred to the secondary. Group of answer choices 0.07+j0.135 0.06+j0.175 0.04+j0.135 0.06+j0.135

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Related questions

Q: We wish to conncct a 6 kVA, 120/240 V transformer as an autotransformer to a 120 V source to supply…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: At the constant rating of a transformer or a synchronous generator when reactive power decreases the…

A: Power factor : Power factor (PF ) is cosine of angle between voltage and current . Reactive power…

Q: 150 kVA, 2800-240 V, 50 Hz transformer. = 0.0082N , Xeg,Ls = 0.0223N Reg.ts Step down transformer…

A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.

Q: The primary of a certain transformer, with and open-circuit secondary, takes 1A at a power factor of…

A: Given I2=50Apower factor ϕ0=0.4power factor ϕ2=0.8

Q: For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is…

A: For a 1-phase transformer, the basic relation is given as:

Q: Two single-phase transformers whose phase electrical equivalent circuits are given below are…

A: Since both the transformer are connected in parallel,we can draw the each transformer equivalent…

Q: Since the first winding leakage impedance of a single-phase transformer with 220/110 V 50 Hz values…

Q: Q10. In a transformer modeling, the value of the impedance referred to primary side is N/N2 P* Z2…

Q: A 20 KVA, 480/2000-V, 50 Hz, single-phase transformer is tested with the following results. Find the…

Q: 502 j1002 25N 400Ω 1:4 2:1 50Ω j100 120V -j1002 1002 u u u m

A: According to the question we have to calculate the value of effective impedance as seen by the…

Q: Two 70 kW single-phase transformers are connected in parallel. The impedances of the first and…

Q: A star connected load with real impedance ZL= 1-j1 Ohm per phase is connected to the secondary of a…

A: The given data about a three phase YNyn0 connected transformer is: Star connected load is connected…

Q: A transformer is rated 1000 MVA kV/345 kV with Z-70.10 pu. If the system base MVA is 500, the…

A: (4) Given that Zpu old=j.10 MVAb old=1000KVb old=13.8KVMVAb new=500 Assume that the new base voltage…

Q: Solve part a & b

A: We can see that, the secondary phase voltage leads the primary phase voltage by 30 degree. Same with…

Q: A transformer shown in Figure 10 is needed that will cause an actual load resistance of 250 to…

A: (a) Redraw the given circuit diagram.

Q: Analysis of an Ideal Transformer Circuit The turns ratio of the step-up transformer in Figure 2 is…

Q: A three phase transformer delivers a load of 66 MW at 0.8 p.f. lagging and 138 KV (line-to-line).…

Q: The approximated equivalent circuit referred to the primary of a loaded single phase transformer is…

Q: 3. At three winding transformer at no-load case, the current flows through the tertiary windings is…

A: Power factor: It tells how much active power is utilized by the circuit from the apparent power. The…

Q: Two 200/400 V, transformers are operated in parallel to share a load power factor leading.…

A: Conditions for Parallel Operation- In order that the transformers work satisfactorily in…

Q: The no-load loss of a transformer at rated voltage is 100 watts at 30 Hz and 300 watts at 60 Hz.…

A: In this question , we will find hysteresis loss at given frequency.... Note:- as per our guidelines…

Q: A 480V/240V, 60Hz single transformer has Z1 = 0.1+j0.22 ohms and Z2 = 0.035 + j0.12 ohm. Find the…

A: Given: A single phase transformer with Operating frequency, f=60 Hz Voltage ratio, V1:V2=480/240 V…

Q: DHA) a) Draw an equivalent circuit of a current transformer and derive expressions for ratio and…

A: a) Current transformers- These are those type of transformers, which are mainly used for measurement…

Q: Given a 10 KVA, 1200/240 V, 50 Hz single-phase transformer with an impedance Z1,p = 10+j20 Ohms…

A: In this question we will find turn ratio and primary impedance referred to secondary..

Q: A 30 kVA, 2400/120V., 50Hz transformer has a high voltage winding resistance of 0.1Ω and a leakage…

Q: Q2) For the linear transformer shown in figure below, find: a) Construct a frequency – domain…

A: Solution- (a) Frequency-domain equivalent circuit- In the given circuit, Inductance, resistance and…

Q: A generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:20), and a transmission…

A: Most of human energy requirement is meet by generating electrical energy. Once electrical energy is…

Q: a step-down transformer of 23 kVA, 2300 V / 230 V, 50 Hz, R1 = 4 Ω, X1 = 12 Ω, R2 = 0.04 Ω, X2 =…

A: a) Calculate the rated current by substituting the values of V=230 V, P=23 kVA in the power…

Q: transformers and VA) connectéd in parallel as shown in the following figure. %Z1=2% ST1 Zeq1 SL1 SL2…

Q: Two single-phase transformers whose phase electrical equivalent circuits are given below are…

Q: 6. 150 kVA, 2800-240 V, 50 Hz transformer. Reg.Ls = 0.0082N , Xeq.Ls = 0.02230 Step down transformer…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: A load of 200 kW at 0.85 power factor is to pe shared by two transformers A and B aving the same…

Q: A A-A transformer bank consists of three individual transformers each with its rating given in the…

A: NOTE:" Since you have a posted a question with multiple sub parts, we will solve first three sub…

Q: Two transformers A and B are connected in parallel to a load of (2+j1.5) ohms. Their impedances in…

A: Given,ZL = 2+j1.5 ΩZA=0.15+j0.5 ΩZB=0.1+j0.6 ΩEA=207 VEB =205 V

Q: A 600 kVA single phase transformer with 0.012 pu resistance and 0.06 pu reactance is connected in…

A: Given that , there are two transformer of 600 kVA and 300 KVA We will refer the concept of parallel…

Q: A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 16 + j120…

Q: Quèstion 9 "Under saturated core condition, transformer become a source of harmonics" True False

A: A transformer is an electrical machine used in an AC circuit to either step up or steps down the…

Q: 3. A three-phase Y-Y transformer is rated at 25 MVA, 13.8-kV:69-kV and has a single-phase equivalent…

A: Given Rating P=25 MVA Impedance ZeqL=62+j388 mΩ (a) The rated current on the low-voltage side of a…

Q: 6. A 5,000-kVA, 3-phase transformer, 6.6/33-kV, NY, has a no-load loss of 15 kV and a full-load loss…

A: In this question 3 phase transformer delta -star is given....We have to find out primary voltage…

Q: A 4800/240-V, single phase transformer is rated at 10 kVA. It has an equivalent impedance referred…

Q: A three-phase Y-Y transformer has specifications of 25 MVA, 15/200 kV and an equivalent series…

A: The solution is given below

Q: 4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters:…

Q: For a 50 kVa distribution transformer, which on its high voltage side is 2400 V and on the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: A transformer may be used to provide maximum power transfer between two AC circuits that have…

A: Given: A transformer may be used to provide maximum power transfer between two AC circuits that have…

Q: Two 11000/400 V, transformers are operated in parallel to share a load of 250 kVA at 0.85 power…

A: Given data: transformer ratings: 11000/400 V total load : 250 KVA power factor: 0.85 for transformer…

Q: A single-phase transformer 11000/420 V, 50 kVA, 50 Hz has resistance and leakage reactance as…

Q: A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 18 + j80…

Q: A single-phase transformer, working at unity power factor has an efficiency of 90 % at both half-…

Q: please solve the part g , h , i

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

A 480V/240V, 60Hz single transformer has Z1 = 0.1+j0.22 ohms and Z2 = 0.035 + j0.12 ohm. Find the equivalent impedance in ohm referred to the secondary.

Group of answer choices

0.07+j0.135

0.06+j0.175

0.04+j0.135

0.06+j0.135

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given Zo-j407 2, R₁143, R6317 52 and a 0.04, what is the magnitude of the source voltage Vs (in V rms) in the primary of the ideal transformer? Vs R₁ ww Answer: Zc Zc R₁ Use up to 2 digits after the decimal point if necessary in your answer below VL-28020 V TR
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
The resistance and reactance of the primary winding of a 440/110 V single phase transformer are 4.4 ohm and 8 ohm respectively. The resistance and reactance of the secondary winding are 1.6 ohm and 2ohm respectively. Then find the equivalent resistance, reactance and impedance referred to the primary side.
A 480V/240V, 60Hz single transformer has Z1 = 0.1+j0.22 ohms and Z2 = 0.035 + j0.12 ohm. Find the equivalent impedance in ohm referred to the Primary Group of answer choices 0.24+j0.62 0.14+j0.62 0.24+j0.7 0.14+j0.7
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
The efficiency of a transformer at load 0.8 p.f. Lag is -- at load 0.8 p.f. Lead * equal less than more than none of these
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
A star connected load with real impedance ZL= 1-j1 Ohm per phase is connected to the secondary of a three-phase Ynyn0 connected transformer. The equivalent impedance per reduced phase of the transformer to the primary is Zeq1= 1+j5 Ohm. The nominal primary voltage is V1Ln= 5920 V and the conversion ratio is a= 10. what is the amplitude of the actual voltage falling on one phase of the specified load? (simplified equivalent circuit will be used).
A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and secondary resistances are 0.55 ohm and 0.035 ohm respectively. The corresponding leakage reactances being 4.22 ohm and 0.18 ohm. The load is equivalent to a coil of resistance 3.85 ohm and inductive reactance of 4.2 ohm. Determine the terminal voltage of the transformer and the output in kW when supplying a given load using approximate equivalent circuit when the applied voltage is 7912 V. Your answer
ََQ/ 400/200 V, single-phase transformer is supplying a load of 50A at a power factor of 0.866 lagging. The no-load current is 2A at 0.208 p.f. lagging. .. Find The primary current is ...... A * The primary power factor is ........ lagging *
primary of a certain transformer takes 1 a at a power factor of 0.4 when it is connected acrossa 200-v, 50-hz supply and the secondary is on open circuit. the number of turns on the primary istwice that on the secondary. a load taking 50 a at a lagging power factor of 0.8 is now connectedacross the secondary. what is now the value of primary current ?