A 3D solid component is subject to external forces such that following three principal stresses are generated: -51MPa, 207MPa and. -327.87MPa. The component is made from a ductlie metal with a Yield Strength of 400MPa Determine for an element of stress subject to these stresses: the Maximum Shear Stress (Answer in MPa only). the Octohedral Shear Stress (Answer in kPa only). the Hydrostatic Stress (Answer in Pa only). the Tresca Effective Stress (Answer in MPa only). the von Mises Stress (Answer in Pa only) Select the 5 correct answers from the list below/:

A 3D solid component is subject to external forces such that following three principal stresses are generated: -51MPa, 207MPa and. -327.87MPa. The component is made from a ductlie metal with a Yield Strength of 400MPa Determine for an element of stress subject to these stresses: the Maximum Shear Stress (Answer in MPa only). the Octohedral Shear Stress (Answer in kPa only). the Hydrostatic Stress (Answer in Pa only). the Tresca Effective Stress (Answer in MPa only). the von Mises Stress (Answer in Pa only) Select the 5 correct answers from the list below/:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the following data, using Mohr's circle of stress and trigonometry, (a) Find the principle stresses and show their sense in properly oriented element and (b) find the maximum (principle) shear stresses with the associated normal stresses and show the results on a properly oriented element.
A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.
In the following Figure using given material properties.a) Determine the internal forces and stresses at both parts after 110 oC temperature increase.b) Determine the new position of B with respect to the point A.
in the figure as shwon: Member AB and BC are made of the same material. it was tested that the same alloy material of 25mm square bar has an ultimate stress of 12kN. determine the required sectional area of bar AB and BC based on the tested material.
At point O of a part subjected to plane stress made of steel material (E = 210 GPa and %3D ww v= 0.3) The tensile components are given below. 240 %3D - 30 MPa *yz yz a) The principal stress components (01, 02 and o3) and their angles with respect to the x-y-z axes of the planes where they are formed calculate b) Calculate the maximum shear stress (tmax) and the angles of the plane in which it is formed with respect to the x-y-z axes. c) Drawthe 2-D and 3-D Mohr circles for the stress components. d) At point O in a section plane passing through point O and having an angle of 30° counterclockwise with the +x-axis Calculate the resulting stress components. e) Calculate the strain components (Exx, EW, Ezz, YXV, YXz and Yyz) and draw the 2-D and 3-D Mohr circles for the strain components.
A 10000N tensile force is used to pull a cylindrical rod with an initial diameter of 2 cm. During the pull, the rod's diameter decreases to 1.8 cm. What is the true stress?i ll rate. S
Please answer as per question and in clear handwriting. The state of stress at a point in a structure is shown in the following figure.Decide:(a) The forces acting on an element oriented at an angle in the directioncounterclockwise θ = 15° from the x-axis (Show the results in a sketch ofcorrectly oriented)(b) find the main stresses (Show the results on a sketch ofcorrectly oriented)
The state of stress at a point under plane stress 40 MPa, Oyy condition is Ox = = 100 MPa and Txy 40 MPa. This radius the Mohr's circle representing the given state of stress in MPa is:
1. At a point in a piece of elastic material, direct stresses of 92 MN/m2 tensile and -49 MN/m2 compressive are applied on mutually perpendicular planes. The planes are also subjected to a shear stress. If the greater principal stress is limited to 100 MN/m2 tensile, determine the value of shear stress. Give you answer to 2 significant figures in MN/m2
Answer the questions below for the following system. Young's modulus and Poison's ratio can be taken as 200 GPa and 0.3, respectively. a) Calculate and determine the stress state for point H using undergraduate level solid mechanics knowledge? b) Determine the principal stress values at point H using undergraduate level solid mechanics knowledge Top view of section where H is located O Point H 300 mm 120 mm 540 mm .H Diameter of the pipe d=36 mm P=900 N
For the following state of stress, (a) using the general equation of transformation of stress, find normal and shear stress, (b) find the principle stresses and show their sense in properly oriented element and (c) find the maximum shear stresses with the associated normal stresses and show the results on a properly oriented element.
Problem2.: The cubic element of the solid body is subject to the stress state shown in Figure, where: дх3D 50 МPа, Ту- 30 МРа, Oy Дх3D 80 MPа, Determine principal stresses using "yx both analytical method and Mohr circle, as well as principal directions (using Mohr circle only). Draw the Mohr circle and physical plane. dz dx dy