A 3-phase Y-connected source (400V) supplies a 3-phase Y-connected load (3xZload = 27 + 9.0 ohm) via a non-ideal, three-core cable. No neutral line is available. Each conductor of the cable has an impedance Zcable = 80 + 2.1 mOhm a. Measure the phase shift angle between line voltage and phase voltage.

A 3-phase Y-connected source (400V) supplies a 3-phase Y-connected load (3xZload = 27 + 9.0 ohm) via a non-ideal, three-core cable. No neutral line is available. Each conductor of the cable has an impedance Zcable = 80 + 2.1 mOhm a. Measure the phase shift angle between line voltage and phase voltage.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.36P: Three single-phase two-winding transformers, each rated 25MVA,34.5/13.8kV, are connected to form a...

See similar textbooks

Similar questions

Three single-phase two-winding transformers, each rated 25MVA,34.5/13.8kV, are connected to form a three-phase bank. Balanced positive-suence voltages are applied to the high-voltage terminals, and a balanced, resistive Y load connected to the low-voltage terminals absorbs 75 MW at 13.8 kV. If one of the single-phase transformers is removed (resulting in an open connection) and the balanced load is simultaneously reduced to 43.3 MW (57.7 of the original value), determine (a) the load voltages Va,Vb, and Vc; (b) load currents Ia,Ib, and Ic; and (c) the MVA supplied by each of the remaining two transformers. Are balanced voltages still applied to the load? Is the open transformer overloaded?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Consider the system shown in Figure 1. Assume the load voltage (VL) is 4720 V and the load consumption is 80 kVA at 0.85 lagging power factor. The line impedance (Zline) is 4.6+j8.5 2. The parameters of the 14,400/4800-V single-phase transformer referred to the secondary are: Req=0.95 , Xeq = 1.74 , Re = 48.5 kn, and Xm = 31.1 k. vp avs 4.6 +19.52 Zline Vs ~ P a:1 ele rmis alf Reais leee V₂ zí S Figure 1: System for Q1 I wad a) Find the current of the load. b) Find the primary and secondary voltages of the ideal transformer. nuomo I un cucc + Bline Xeq,s 1 V₂² 95, 74-32 1. VL 4720 Ponerlosture -> Pont IL = V₂ -V₂ Zine
Transkrmers phase with each bank with - adjuste 35. Three single-phase transformers, cach of 100 kVA rating, are conected in a closed-delta arrangement. If one of them is taken out, it would be possible to load the bank in such a manner that cach one is loaded to the extent of: A 86.6 kVA C. 57.7KVA B. 66.7 kVA D. 33.33 kVA when load is at unity power factor. 36. Average power factor at which V-V bank separate is A 86.6% C. 66.67% В. 73.3% D. None of these 37. Scott connections are used for: A. single-phase to three-phase transformation C. three-phase to two-phase transformation B. three-phase to single-phase transformation (D Any of the above 38. The current in low voltage winding of a 25 kVA, 6600/400 V, 50 Hz, 3-phase Y-A transformer, at full load is: A 36 A Č. 65,32 A B. 20.78 A D. 40.2 A 39. The current in high voltage winding of a 20 kVA, 2200/220 V, 50 Hz, 3-phase A-A transformer, at full load is: (A. 3.03 A C. jo.5 A B. 5.25 A D. None of above 40. The current in low voltage…
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
One advantages of load balancing is that each phase conductor carries the ? current value
H.W 6: For the systom shown, determeine the fauttt level and short cerint current for a 3-phase fault at the of The linee. middle ofone のC) Vo.2 P.u t02p.u ikV 132 ICV =110 p.u 132KV Assume all reactances of generatos and transfe ona 10% u kV at aen's. on common base, Sb- 50 MVA,
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3 phase side. The main transformer primary to secondary turns ratio is (12/1).
Consider a 3-phase, 33 kV transformers with N1:N2 = 900:150. Calculate the secondary line voltage on no load condition the windings are connected in the following configurations i) Star-Delta. ii) Delta-Delta tes
Three single-phase transformers (ideal) are connected as shown in the figure below to supply a balanced 3-phase, 150 KVA, 600 VL load from primary 4.16 KVLL line. H1 X1 H2 X2 BALLANCED H1 X1 THREE PHAGE LOAD H2 X2 H1 X1 X2 (a) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram:f
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
Please help with this balanced three-phase circuit problem.