A 20-mm-thick plate is bolted to the flange of a T-beam to form a -200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm

A 20-mm-thick plate is bolted to the flange of a T-beam to form a -200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The gusset is riveted to a larger plate by 4 – 22mm rivets in single shear arranged andloaded as shown. Calculate the stress in the most heavily loaded rivet.
For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
The steel tie bar shown is to be designed to carry a tension force of magnitude P = 120KN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel to be used, the maximum allowable stresses are: o = 180 MPa, t = 120 MPa, op = 380 MPa. Design the tie bar by determining the required values of: a. the diameter d of the bolt, b. the dimension b at each end of the bar, c. the dimension h of the bar.
A plate with width of 300mm and thickness of 20mm is to be connected between two plates 12mm thick with same width by 4-25mm diameter rivets a shown. The rivet holes have a diameter 2mm larger than the rivet diameter. The plate is A36 steel with yield strength Fy=248 Mpa and Fu-400MPa. The rivets have nominal shear stress capacity of 165MPa. O 803 O 1490 • Determine maximum load (P1) that can be applied without exceeding design tensile stress in plates (consider yielding and rupture of plates ONLY) in KN O 1180 O 1340 ο ο ο ο ο P3 O 1968 O 590 O 670 O 893 O 707 OO 150 O 1180 P1 P2
A flange bolt coupling consist of 8-12.7mm steel bolts on a circle diameter of 304.80mm & 6-12.7mm steel bolts on a circle diameter of 228.60 mm. is subjected to a 950KN-mm torque.The shear stress developed in the outer circle of the flange bolt coupling is ___ MPa. (A) 1.50 B 6.80 (C) 3.20 (D) 4.30 E 8.10
The five-bolt connection shown must support an applied load of P = 400 N. The thickness of the axial member: = 1 mm. and the width = 16 mm If the ultimate shear stress in the bolts must be limited to 250 MPa with F.O.S = 2.5 . And the ultimate normal stress in the axial member = 180 MPa, with F.O.S = 2.9 , And the ultimate bearing stress in the axial member = 95 MPa, F.O.S = 1.3 Determine the minimum bolt diameter that may be used in the connection? In correct way
The five-bolt connection shown must support an applied load of P = 300 N. The thickness of the axial member: = 1.5 mm. and the width = 18 mm If the ultimate shear stress in the bolts must be limited to 265 MPa with F.O.S = 3.7 . And the ultimate normal stress in the axial member = 250 MPa, with F.O.S = 2.8 , And the ultimate bearing stress in the axial member = 110 MPa, F.O.S = 2.5 Determine the minimum bolt diameter that may be used in the connection
For the connection shown, the bolt diameter is d = 15 mm. The average shear stress in the bolts must be limited to 210 MPa. Determine the maximum load P that may be applied to the connection based on the shear strength of the bolts.
The five-bolt connection must support an applied load of P = 149 kips. If the average shear stress in the bolts must be limited to 50 ksi, what is the minimum bolt diameter that may be used for this connection? P Answer: d = i in.
1. Two plates each with thickness 7-160mm are bolted together with 6-22 mm dia. bolts forming Bolt 52= 80mm spacing are as follows S₁ = 40mm Bolt hole dia. 25mm S3 = 100mm L fu- 483 тра ту- 345 тра Solve the allowable istrength and the P a Ultimate strength in: 1- Yielding 2. Rupture 3. Shear 4. Block Shear oo lap connection atat
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
For the given riveted connection shown, having the allowable stresses: Fy = 248 MPa Fy = 150 MPa (shear stress) Tensile stress=0.60 Fy Bearing stress = 1.35 Fy Rivet hole has a diameter 2mm greater than the rivet diameter. The main plate has a width of 300mm and a thickness of 20mm. Determine the diameter of rivets such the shear capacity of the rivets is equal to its bearing capacity. Also, compute the maximum value of P so as not to exceed the allowable tensile stress of plates. P- O JAK O O 300 mm -P/2 -P/2