5. Which term is INCORRECTLY defined? a. linear range - the range over which the response of an analytical method is proportional to analyte concentration b. dynamic range - concentration range over which there is a measurable response to analyte, though the response is not linear c. blank solution - a solution containing all reagents and solvents used in the analysis to which no analyte is deliberately added d. standard solutions - solutions for which the standard deviation is known 6. True or False: Internal standards correct random error caused by run-to-run variation. a. True b. False

5. Which term is INCORRECTLY defined? a. linear range - the range over which the response of an analytical method is proportional to analyte concentration b. dynamic range - concentration range over which there is a measurable response to analyte, though the response is not linear c. blank solution - a solution containing all reagents and solvents used in the analysis to which no analyte is deliberately added d. standard solutions - solutions for which the standard deviation is known 6. True or False: Internal standards correct random error caused by run-to-run variation. a. True b. False

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter12: Spectrochemical Methods

Section: Chapter Questions

Problem 7P

See similar textbooks

Similar questions

. 100 ml boiled cooled and filtered water sample takes 9.6 ml of M/50 EDTA in titration. The Permanent hardness of the water sample in terms of ppm of CaCO3 equivalent is
You find that for your analysis, your response factor (adjusted for internal standard) for a particular analyte was 0.0104 ppm. When you run a sample mixture, the integration for that component is 2,186, and the integration for the internal standard is 14,139. What is the concentration of the component in ppm? (Enter the numerical value without units.)
A method of quantitative determination of the concentration of constituentsof a sample analyzed by gas chromatography is area normalization. Thiscomplete elution of all sample constituents is required. Thearea of each peak is measured and corrected for the detector response to the diffe- renteseluatos. This correction involves dividing the area by an empiricalcorrection factorDetermined. The concen ration of the analyte is found from the ratio between itscorrected and the total corrected area of all peaks. For a chromatogram containing threerelative areas were determined as 16.4; 45,2; and 30.2, in the order ofincreased retention time. Calculate the percentage of each compound if therelative responses from the detector are 0.65, 0.73 and 0.85, respectively.
In analytical chemistry, when and why do we do representative sampling?
16) Which of the following(s) is/are correct? I- Selectivity factor is the amount of time a solute spends in the stationary phase relative to the time it spends in mobile phase II- The retention time for an analyte is the time interval between its injection onto a column and its appearance at the detector at the other end of the column. III- Distribution constant is the ratio of the total solute concentration in the stationary phase to that in the mobile phase. A) I, II and III B) Only II C) I and III D) II and III E) Only III for GC2
what can be an analyte for using internal standard? sample: vegetable oil containing ethyl oleate, IS: Ethyl oleate. what should be analyte here (what mixture composions) to use for internal standard method and calibration?
1. These are balances that have a maximum loading of 10 to 30 g with a precision of 60.01 mgA. semi-microanalyticalB. MicroanalyticalC. MacrobalancesD. Triple Beam Balance2. Which type of curve is normally produced when plotting the change in the concentration of a specie of some function and the amount of reagent added?A. Titration curveB. Sigmoidal CurveC. Phase Transition curveD. Calibration curve3. In the dead dear case study, silver diethyldithiocarbamateforms a colored solution when it binds with arsenic, what do we call substance like silver diethyldithiocarbamate?A. Secondary standard reagentB. Precipitating agentC. Chelating agentD. Primary standard reagent
Ooldtion Table 1. Measurements for standardization of NaOH Trial 1 Trial 2 Trial 3 1] Tared mass of KHC3H4O4 (9) 0.374 0.325 0.357 12] Burette reading of NaOH, initial (mL) 4.59 3.61 4.03 [3] Burette reading of NaOH, final (mL) 22.03 18.77 21.17 Part B. Molar Concentration of an Acid Solution Enter the number corresponding to the type of acid you have 1. HA 3 2. H2A 3. H3A Enter the unknown number. 21 Table 2. Measurements for titration of unknown acid Trial 1 Trial 2 Trial 3 [1] Volume of acid (mL) 25.0 25.0 25.0 [2] Burette reading of NaOH, initial (mL) 2.13 2.48 3.68 [3] Burette reading of NaOH, final (mL) 24.10 24.52 25.56 Part C. Percentage by Mass of an Unknown Solid Enter the number corresponding to the type of acid you have 1. HA 3 2. H2A 3. H3A Enter the unknown number. 30 Molar mass of the unknown acid 192.14 Table 3. Measurements for titriation of solid Trial 1 Trial 2 Trial 3 [1] Mass of sample (g) 26.334 29.157 27.111 [2] Burette reading of NaOH, initial (mL) 3.21 1.48…
Define , describe, or illustrate the following: a. HETPb. Capacity factorc.. Selectivity factord. Chromatograme. Elution
What is the role of specific visualizing agents in a Thin layer Chromatography? Please shortly answer at your own words. Answer should be to the point (4-5 lines).
Researchers used gas chromatography to determine the % v/v methyl salicylate in rubbing alcohol [Van Atta, R. E.; Van Atta, R. L. J. Chem. Educ. 1980, 57, 230-231]. A set of standard additions was prepared by transferring 20.00 mL of rubbing alcohol to separate 25 - mL volumetric flasks and pipeting 0.00 mL, 0.20 mL, and 0.50 mL of methyl salicylate to the flasks. All three flasks were diluted to volume using isopropanol. Analysis of the three samples gave peak heights for methyl salicylate of 57.00 mm, 88.5 mm, and 132.5 mm, respectively. Determine the % v/v methyl salicylate in the rubbing alcohol.
Which error will lead to negative deviation from the theoretical Keq? a. cuvette was filled to the brim with the sample. b. cuvette was washed with sodium hydroxide instead of distilled water. C. standard with the highest concentration was used in autozero. d. cuvette was misplaced such that the opaque side faces the light