5. Compute the normal tension which will be applied to a tape supported over two supports in order to make the tape equal to its nominal length when supported only at the end points. The steel tape is 30m long and weighs 0.84kg when supported throughout its length under a standard pull of 5.6kg with the modulus of elasticity is 2x10^6 kg/cm^2 and area of 0.06 cm^2. a. 17.33kg b. 15.92kg c. 16.55kg d. 18.10kg

5. Compute the normal tension which will be applied to a tape supported over two supports in order to make the tape equal to its nominal length when supported only at the end points. The steel tape is 30m long and weighs 0.84kg when supported throughout its length under a standard pull of 5.6kg with the modulus of elasticity is 2x10^6 kg/cm^2 and area of 0.06 cm^2. a. 17.33kg b. 15.92kg c. 16.55kg d. 18.10kg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam A, = 1,520 mm² fu= 27 MPa (cylinder strength) f = 3.5 MPa (modulus of rupture) fy= 400 MPa Calculate the stresses caused by a bending moment M = 60 kN *m 650 (unit: mm) 250 D25 y 600
A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40 mm, 50 mm and 60 mm respectively. If the bar is subjected to an axial load of 10 kN, the total elongation of the bar would be (E is the modulus of elasticity in KN/mm². (a) 4/1 1 1 + + (b) TE 16 25 36 (c) 1 0.4 1 1 + wwwwww + TE 16 25 36 (d) 4√2/1 1 1 www + wwwwwww + TE 16 25 36 40/1 1 1 + TE 16 25 36 — ===== + — mm mm mm mm
Given the image below what is the equivalent force-bouple at poitn A at tension of cord Cg when Tcg = 52.1N?
A horizontal 50 kN load is applied on a 610UB125 Beam as shown in Figure 4. Determine the stresses at four corners A, B, C and D. Also, determine the angle that the neutral axis forms with the horizontal plane. The sectional properties are given in Table 1. 50k! 306 50 KN Table 2. Figure 4 (unit in mm) 306 mm bf d Y, A tr tw Section mm² mm mm mm mm 610UB125 16000 229 612 19.6 11.9 Sx lyo Sy (x106 (x10³ (x106 (x10³ mm²) mm³) mm²) mm³) 986 3680 39.3 536
What pull in kilogram (normal tension) is required in order that the effect of sag will be eliminated when the tape is supported at end points only? The tape has a standard pull of 8kg. The tape’s cross-sectional area and modulus of elasticity are 0.05m^2 and 200 GPa, respectively. *
When solving the problems for Section 1.6, assume that the material behaves linearly elastically. Problem 1.6-1 A high-strength steel bar used in a large crane has diameter d-50 mm (see figure). The steel has modulus of elasticity E-200 GPa and Poisson's ratio -0.3. Because of clearance requirements, the diameter of the bar is limited to 50.025 mm when it is compressed by axial forces. What is the largest compressive load Pas that is permitted? Lateral strain
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
A wide flange A60 steel column has a length of 6.4meters and pinned ends. If Sx=888x103 mm3, Sy=128x103 mm3, d=358mm, bf=184mm, A=7,289mm2, Fy=414MPa, calculate the critical buckling stress, Fcr in MPa of the column. Express your answer in one decimal place.
Photos 4 Crop & rotate Filters * Adjustments 2 Undo all Redo all Crop & rotate Straightening 0 ° Two round bars are joined and used as a tension member as illustrated. The modulus of elasticity is 200 GPa for steel and 70 GPa for aluminum. Rotate D4 Flip O Aspect ratio : Custom Aluminum 100 mm diameter Reset bar 50 mm diaineter P Steel bar +280 mm 400 mm Determine the magnitude of the force P (in kN) that willI lengthen the two bars 0.45 mm. * Your answer Save a copy Cancel 6:50 PM O Type here to search 日 28°C Partly cloudy 4)) ENG 23/09/2021
L For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 17 kN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm tf = 20 mm tw = 15 mm %3D b tw O bending MPa Round to one decimal place
The beam is loaded as shown. which of the following nearly gives the flexural stress due to tension in MPa? 240 mm W = 12 KN/m 60 mm 200 mm 4 m 4 m 4 m 60 mm 202.967 none among the choices 165.856 105.802 OO O O
(40 Hiw A Pismatic steel bar ofa Square cross section (loo*lo0)mm is looled by Comressive force P= 1300 kU, the bar has length 2.5 m, Eg=200 G Pa, V=0.3,determine the Shortening d, the increase in the dimensions of cross Section , the change in Volume DV of the bar? loomm Joomm