4. The maximum stress a human tendon can withstand is estimated to be 1200 MPa. If you were to test it for rupture what load cell you should use (250N or 5kN) what problems may occur if you select an incorrect load cell. 5. The figure below is a J-shaped (or concave upward) stress-strain curve. What does a J-shaped stress stain curve indicate about a material's response to stress and tendency to yield? Name two materials that have J-shaped stress strain curves.

4. The maximum stress a human tendon can withstand is estimated to be 1200 MPa. If you were to test it for rupture what load cell you should use (250N or 5kN) what problems may occur if you select an incorrect load cell. 5. The figure below is a J-shaped (or concave upward) stress-strain curve. What does a J-shaped stress stain curve indicate about a material's response to stress and tendency to yield? Name two materials that have J-shaped stress strain curves.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You need the shear modulus for a particular material in order to calculate shear strain for a known applied shear shear stress. You can't find shear modulus for the material, but you can find elastic modulus (200 GPa) and Poisson's ratio (0.3). Which of the following could you use as the shear modulus for your calculations? 200 GPa O 60 GPa O 77 GPa O 154 GPa
Two different materials designated A, and B, are tested in tension using test specimens having diameters of 0.505 cm and gage lengths of 2.0 cm (Figure 1). At failure, the distances between the gauge length marks are 2.13 cm (sample A) and 2.48 cm (sample B). Also, at the failure cross-sections, the diameters are found to be 0.484 cm (sample A) and 0.398 cm (sample B), respectively. i. Calculate the percent elongation and percent of area reduction in each specimen. a. Sample A b. Sample B ii. Classify each material as brittle or ductile using your judgement.
Sketch a representative stress-strain digrama for a ductile material showing the following on it (label the axis and provid units). 1- YIELD STRENGTH. 2- TENSILE STRENGTH. 3- FRACTURE POINT. 4- HARDENING PART. 5- SOFTENING PART. 6- A METHOD TO CALCULATE THE STIFFNESS. 7- A METHOD TO CALCULATE THE DUCTILITY.
Given the following stress-strain graph:a. is the modulus of elasticity of "A-514" greater, less or equal to the one of "A-572"?b. from the previous question, make an estimatio for both of them, check that the graphic comes in %c. If we were to test these materials in a universal tension equipment, which one would withstand more load?d. If we were to test these materials in a universal tension machine, which one would elongate the most before fracturing? would elongate the most before fracturing? e. Of the 6 materials shown, do any behave as brittle materials? f.
The figure below is a stress strain curve for an alloy of aluminum at various temperatures. a) What is the yield stress at room temperature? b) Assume a rod made of this material is 20 cm long and at room temperature. If the rod were put in tension, how long would it be when it breaks? c) If the rod has cross-sectional area 1 cm?, what force is required to break it (in tension)? Longitudinal RT 250F 350F 30 500F 0.002 0.004 0.006 0008 QO10 O012 Strain, in/in. A-93 Stress, ksi
Given: Stress strain curve of 10 mm diameter and 1 m long ductile stainless-steel rod. 900 800 700 600 500 Mild 400 Stainless 300 200 - 100 0.1 0.2 0.3 0.4 Strain 0.5 0.6 0.7 Draw stress-strain curve for compression here 1. Label all points of significance on the stress strain curve 2. Draw the stress-strain curve for the rod in compression and label all points of significance. 3. What is the Young's modulus in tension? Assume .001 strain at 500 MPa 4. What is its Youngʻs modulus in compression? 5. What is the tensile yield strength of this rod using the 0.2% offset criteria? 6. What is the compressive yield strength of the rod? 7. What is force required to yield the rod?. Show calculation: 8. What is the UTS of this rod?. 9. What is the force required to break the rod? Show calculation: 10. What will be UCS of the rod? Stress (MPa)
5. Please calculate the strain and stress in the following two prompts a. A 1 cm long section of tendon stretches to 1.011 cm when it is subjected to a tensile force of 40,000 N. What is the strain in this segment of tendon? @? 17 b. The section of the patellar ligament in the previous question is 0.02 m² in the cross section. What is the stress in this section of ligament as a result of 50,000 N tensile force? E = Δι 19 0 = A 1.011 cm 50000 0,02 Scoco 40000 1.25 = T % 2500000 strain N/m² on trito flox your wrist, you may notice that your
2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a gage length of 2 in. is shown in the figure below. TENSILE STRESS (MPA) 450 400 350 300 250 200 150 100 50 Part A 0 0 STRESS VS. STRAIN 0.002 0.004 STRAIN 0.006 Determine the modulus of resilience. Show units. Part B Determine the modulus of elasticity of the material. Part C Estimate the Yield Strength of the material. 0.008 0.01
Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. 600 500 400 500 300 400 300E 200 3200 100 100E 0.000 0.002 0.004 0.006 Strain ol 0.00 0.16 0.20 0.08 Strain 0.04 0.12 Select one: O The tensile yield strength Sy = 290 Mpa and the maximum strength Smax = 500 Mpa. O The tensile yield strength Sy = 170 Mpa and the maximum strength Smax = 400 Mca. G The tensile yield strength Sy = 200 Mpa and the maximum strength Smax = 500 Moa. O Tne tensile yield strength Sy = 390 Mpa and the maximum strength Smax= 500 Mpa. The tensile yed strength Sy = 150 Mpa and the maximum strength Smax = 250 Mpa. Stress (MPa) Stress (MPa)
After the yield region in the stress-strain curve the strength up to ultimate value because: -Molecules orientation in the direction of applied stress -Molecules fails to withstand the applied stress -Molecules orthogonal to the axis of applied force The following figure shows typical engineering tensile stress vs. strain curves, where: * Stress Strain - Points A, C, E and F correspond to the tensile strength and elongation at yield - Points A, B, D and F correspond to the tensile strength and elongation at break Points A, C, E and F correspond to the tensile strength and elongation at break
For the stress-strain curves below, which statements are correct? Stress (MPa) 60 50 40 30 20 10 0 a. 0 b. O c. e. f. A 1 2 The mechanical behavior shown in C is that of an elastomer with low elastic modulus Polymer B and C have an elastic behavior whereas A has a plastic behavior While the deformation in polymer A is fully reversible until breakage, polymer B and C only display reversible deformation until 0.1X and 5x elongations respectively Od. The polymer with brittle nature is the one that possesses the highest elastic modulus The mechanical behavior shown in B is that of an elastomer with low elasticity The polymer with the necking behavior has the highest strength B с 3 4 5 6 7 8 Strain
6. State your answers to the following questions.Strain Gauge represents the deformation of a material through a change in resistance. If so, explain how temperature will affect the strain gauge in the experimental environment.①:In this experiment, the Strain Gauge measures the strain in micro units. Explain one possible error factor when applying a load by hanging a weight on the material with the strain gauge attached. (Hint: It is easy to shake by hanging the weight using a thread)①: