4. A multiple disc clutch running in oil is required for a touringmotorcycle. The power demand is 75 kW at 9000 rpm.Space limitations restrict the maximum outer diameter ofthe clutch plates to 200 mm. Select an appropriate liningmaterial and determine the radii for the discs, the number ofdiscs required and the clamping force.5. A multiple disc clutch is required for a high-performancemotorcycle. The power demand is 100 kW at 12 000 rpm.Select an appropriate lining material and determine the radiifor the discs, the number of discs required and theclamping force.6. A multiple disc clutch is required for a small motorcycle. Thepower demand is 9 kW at 8500 rpm. Select an appropriatelining material and determine the radii for the discs, thenumber of discs required and the clamping force.0. oolinor b

Given: P=75 kWN=9000 rpmd0=200 mm

4. A multiple disc clutch running in oil is required for a touring motorcycle. The power demand is 75 kW at 9000 rpm. Space limitations restrict the maximum outer diameter of the clutch plates to 200 mm. Select an appropriate lining material and determine the radii for the discs, the number of discs required and the clamping force.

4. A multiple disc clutch running in oil is required for a touring motorcycle. The power demand is 75 kW at 9000 rpm. Space limitations restrict the maximum outer diameter of the clutch plates to 200 mm. Select an appropriate lining material and determine the radii for the discs, the number of discs required and the clamping force.

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter34: Variable Voltage And Magnetic Clutches

Section: Chapter Questions

Problem 9RQ: What is the primary advantage of an eddy current clutch over a mechanical clutch?

See similar textbooks

Similar questions

(a) State the main advantages of toothed clutches. (b) Uniform wear theory is used in designing a new friction clutch. Explain your ideas and concepts to support the statement. (c) (d) A brand new Street Performace Clutch are capable to delivered 135 Nm torque when the engine's flywheel is rotating at 1400 RPM. The other technical specifications are describe in Table (c). Over the years, the clutch torque performance had reduced to 100 Nm due to wear and tear of the ceramic plate while the others specification was remained unchanged. (i) Assuming the steel plate were made to wear resistance. Examine how much has the ceramic plate worn off on each contact surface individually. (ii) Calculate the transmission power lost in kW. Table (c) Descriptions Clutch plate inner diameter Clutch plate outer diameter Number of ceramic plates Number of metal plates installed Coefficient of friction, µ Coil spring stiffness Number of coil spring installed Specifications 100 mm 200 mm 3 0.3 12,000 N/m 4…
A disc clutch has 6 pairs of contacting friction surfaces. The frictional radius is 2 inand the coefficient of friction is 0.30. An axial force of 100 lb acts on the clutch. Theshaft speed is 400 rpm. What is the power transmitted by the clutch?
Which clutch would you use to connect two spindles with a 250 angle between them? Why you chose this clutch, in terms of uniform moment transmission? Explain that it must meet the requirements.
...A single disc clutch with both sides of the disc effective has outside diameter of 250 mm and inside diameter of 150 mm. The applied force is limited to 20 kN based on axial pressure and the coefficient of friction is 0.25. Which of the following is the total torque that the clutch transmits? Assume uniform pressure conditions.Group of answer choices 510 Nm 1000 Nm 1020 Nm 500 Nm
Write down the parameters considered in determining the basic dimensions of the friction clutch
(c) List the key components in a clutch assembly and explain their role in making the clutch assembly function to transmit power from the engine to the input shaft of a gearbox.
These are Considerations in Designing a Friction Clutch. Can you explain these conditions?The following considerations must be kept in mind while designing a friction clutch.1. The suitable material forming the contact surfaces should be selected.2. The moving parts of the clutch should have low weight in order to minimise the inertia load,especially in high speed service.3. The clutch should not require any external force to maintain contact of the friction surfaces.4. The provision for taking up wear of the contact surfaces must be provided.5. The clutch should have provision for facilitating repairs.6. The clutch should have provision for carrying away the heat generated at the contactsurfaces.7. The projecting parts of the clutch should be covered by guard
Compare three different types of clutches: single plate, conical friction and centrifugal, stating the advantages and limitations of each. Centrifugal clutches are used extensively in motor vehicles, select an appropriate clutch for this application and use the advantages / limitations already detailed, to justify your selection
Establish a formula for the frictional torque transmitted by a cone clutch
Can you explain this table in designing friction clutch?
Select an appropriate clutch system to transmit power from the engine to the compressor of a car air conditioner. Justify your selection. And explain in detail the working principle of the type of clutch you select.
What are the advantages and disadvantages of conical clutches compared with plate friction clutches?