(4) The figures given below show the pole locations of three second-order systems. Assume that @>0o. (a) The step response of which system, (i) or (ii), has a shorter settling time? (b) The step response of which system, (i) or (iii), arrives at it maximum overshoot sooner? (c) The step response of which system, (i) or (iii), is more oscillatory? jo jo 700 35° 70° Wo Wo (i) (ii) (iii) Answer: (a): (b): (c):

(4) The figures given below show the pole locations of three second-order systems. Assume that @>0o. (a) The step response of which system, (i) or (ii), has a shorter settling time? (b) The step response of which system, (i) or (iii), arrives at it maximum overshoot sooner? (c) The step response of which system, (i) or (iii), is more oscillatory? jo jo 700 35° 70° Wo Wo (i) (ii) (iii) Answer: (a): (b): (c):

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 3R: a. What is the ampere rating of the circuits that are provided for the small-appliance loads? _____...

See similar textbooks

Similar questions

The simplified block diagram for position servo mechanism used in the base of arobotic arm is illustrated in Figure. Investigate whether each of this statement iscorrect or false by using root locus approach.(i) The break-away point of the system is at –0.835
I want a solution in less than 30 minutes Often, the network is referred as an infinite bus when a change in input mechanical power or in field excitation to the unit does not cause an appreciable change in a. system frequency or terminal voltage b. Total production cost c. system frequency and terminal voltage d. system frequency alone
A final year project student, Raphael, learns in EEE307 that an oscillator circuit with a differential output can be built using single-ended tuned amplifiers like the one shown below: VDD C₁=R4₁ - Vout VinM₁ Fig. 3.1 Single-ended tuned amplifier schematic (image adapted from B. Razavi ©2012)
QUESTION 1 The unit step response of a second-order open-loop LTI system is shown below Calculate approximate percentage maximum overshoot? Calculate approximate rise time value? (FYI: The rise time is defined as the time system takes from 10% to 90% of the final value) Calculate approximate settling time value? (FYI: The settling time is defined as the time at which the system reaches to steady-state value and remains within the tolerance of plus or minus 2%)
Which of the following error is caused by a reversal of measured property? a) Dead regionb) Noisec) Non-linearityd) Hysteresise) Tolerance
6- Clearance is ...... 7- and are used to improve string efficiency. .. .is used. 9- The main reason of using O.H.T.L instead of underground cables to transfer power is ..... ...... 8- To minimize the fuel cost of power systems, the concept of ... .... a- reliability c- stability 10- Due to non-pure capacitance between conductor and sheath, so leakage current passes (true or false). b- cost
QUESTION 3 a) b) Briefly describe the following terms for a generic second order instrument response. i. time constant (T) ii. rise time (Tr) iii. settling time (Ts) iv. peak time (Tp) Indicate the following characteristics on the generic second order response given in Figure Q3(b). i. Rise Time ii. iii. iv. Settling Time Min Settling Time Max Settling Time V. Overshoot vi. Undershoot vii. Maximum peak viii. Peak Time Amplitude 4 3.5 3 2.5 1.5 1 0.5 0 0 5 Step Response 10 Time (seconds) Figure Q3(b) 15 20 25
What do you mean by cascaded systems? How do you get the total gain or attenuation for such?
Electrical Engineering a) A 240V single phase circuit is run in conduit in 2 core 70°C PVC/PVC cable having live conductor of 2.5 mm? (Ioperating is approximately 20A) and protection conductor cable (cpc) of 1.5 mm?. If the circuit is protected by 30 HRC fuse, with circuit length of 55 m, and ZE is 0.8 2. EVALUATE whether the initial c.p.c. size provided is adequate. Given 2 core PVC/PVC bunched cable impedance is (R1 + R2) = 26.9 m2/m and k = 115.
Discuss the importance of power delivery components like voltage regulators and capacitors on a motherboard and their impact on system stability and overclocking.
2. The impulss resporse kinl * a decree-sime LTI system is shown in Figure tia) Deramine and skotch ha cuput y(n] of this sysaem so the inp.r [x) shown in Figure 1it) without using the corvoluian technique. ta) () gure 1.
(i) A chopper circuit drives an inductive load from 360 DC supply. Given the load resistance as 8 2, the average load current as 20 A and operating frequency is 480 Hz. When the chopper is ON, 7 V is dropped. Calculate (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in two quadrant operation (RL load) and explain its operation. · Duty Cycle ON period OFF period