3c.) The researchers would like each measured data set with a total sample time of 0.2 seconds. Using a sample rate of 1000 [Hz], determine the minimum number of samples that should be collected to achieve the desired sample time. N = [-] 3d.) If the maximum cylinder pressure is 100 psi and the sensor has a sensitivity of 0.05 V/psi, what is the maximum voltage output of the sensor in this setup? Vmax = [V]

3c.) The researchers would like each measured data set with a total sample time of 0.2 seconds. Using a sample rate of 1000 [Hz], determine the minimum number of samples that should be collected to achieve the desired sample time. N = [-] 3d.) If the maximum cylinder pressure is 100 psi and the sensor has a sensitivity of 0.05 V/psi, what is the maximum voltage output of the sensor in this setup? Vmax = [V]

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A generator is feeding the load. A second load will then be connected in parallel with the first load. The generator has an idle frequency of 61Hz and an Sp slope of 1MW/Hz. Load2 draws 800kW active power at 0.707 reverse power factor, while load1 draws 1000kW active power at 0.8 reverse power factor. What will be the operating frequency of the system after load 2 is connected? *Please explain the solution step by step
Comment briefly on the relationship between input and output power at varying excitation levels and on the relationship between excitation and power factor or reactive power, when the synchronous machine is connected to an infinite busbar
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
Q3/ A/ Compare between de series and shunt generator. Q3/ B/ Briefly explain the commutating process in dc machine.
A shunt generator on dest is separately encited and driven at 1000 rev /min. The open circuit test chars. are given Field test CA o 0'157 O.477 0 663 O.805 1.0 129 Induced Emf CU) 12a5 300 400 100 450 500 550 ine mlc is then shunt Connected and gun at l000 revlmine with a constant field cicuit esistance of 540R. The agmature docuit resistamee is er. Deduce and plot the load Chargaetesistics of this mle,negleeting effeetof amarterre reaction.what is value of manimum lbud cursrent.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
Frequency of emf in the stator of a 8 pole induction motor is 50Hz and the rotor emf frequency is 1Hz. The motor speed is ................ Answer
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
A value of magnetizing current in a 3-phase induction motor * gives power factor smaller .. larger smaller. .poor large . better O large...poor O
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
A 3 phase, 1500 rpm, 2200 V, star connected synchronous motor has an impedance of 0.4+j90 per phase. At some excitation 2900 V is induced in the armature. Find the maximum torque developed by motor before the motor breaks out of synchronism. Also find the load angle this time.
X AC docs.google.com/forms/d/e/1FAlpQLSfa1_Fcy2z3FUBw2-aDiF Translate Map gmail M pdf convert ugKJI jsbao P äwly Jguaáll A smallpdf Section 5: Choose the correct Answer What happens if field winding of the synchronous motor is short * circuited First, starts as induction motor then run as synchronous motor Not start Motor will burn out Run as induction motor ( ( هذا السؤال مطلوب La dn j When the field of a synchronous motor is over excited, the power factor * will be Leading O Lagging O Zero O Unity O * The synchronous motors are not self-starting because The direction of torque on the rotor reverses after every half cycle. Slip is not present in synchronous machine O hp O O O