3. What tests can be performed to determine if an emulsion is w/o or o/w? a. fluorescence test b. dye test c. dilution test d. electrical conductivity e. All of the above 4. Calcium Hydroxide Solution (Lime Water) and olive oil are used because an emulsifying agent is formed in situ when these 2 solutions are agitated together. What is the emulsifying agent that is formed? a. calcium succinate b. calcium oleate c. succinic hydroxide d. palmitic hydroxide

3. What tests can be performed to determine if an emulsion is w/o or o/w? a. fluorescence test b. dye test c. dilution test d. electrical conductivity e. All of the above 4. Calcium Hydroxide Solution (Lime Water) and olive oil are used because an emulsifying agent is formed in situ when these 2 solutions are agitated together. What is the emulsifying agent that is formed? a. calcium succinate b. calcium oleate c. succinic hydroxide d. palmitic hydroxide

Physical Chemistry

2nd Edition

ISBN:9781133958437

Author:Ball, David W. (david Warren), BAER, Tomas

Publisher:Ball, David W. (david Warren), BAER, Tomas

Chapter7: Equilibria In Multiple-component Systems

Section: Chapter Questions

Problem 7.31E

See similar textbooks

Similar questions

1. Explain why coconut oil and palm oil are immiscible and miscible at a particular solvent. 2. Explain the translucent spot observed when coconut oil is brought in contact with paper. 3. What mixture yield permanent emulsions?
How much of the preservative is needed to prepare a 120-mL preparation of Aluminum hydroxide gel based on this formulation? Ammonium alum 800 g Sodium carbonate 1000g Peppermint Oil 0.01% (0.01 g/100mL) Sodium benzoate 0.1% (0.1 g/100mL) Purified water, qs ad.2000 mL a. 0.12 g b. 60 g c. 48 g d. 0.012 g
6. Describe the differences between flocculated and deflocculated suspensions. 7. What is the purpose of a wetting agent in a suspension dosage form?
How much of the suspending agent is needed to prepare a 60-mL preparation of Aluminum hydroxide gel based on this formulation? Ammonium alum 800 g Sodium carbonate 1000g Peppermint Oil 0.01% (0.01 g/100mL) Sodium benzoate 0.1% (0.1 g/100mL) Purified water, qs ad. 2000 mL a. 0.06 g b. 30 g c. 24 g d. 0.006 g
Which of the following is/are proper lab techniques in solution preparation? Choose one or more best answer: a. Quickly adding 90mL of distilled water onto 10mL of concentrated acid to make 100mL of diluted acid solution b. Adding NaOH pellets in the volumetric flask and immediately diluting to mark c. Quantitatively transferring dissolved solids from a beaker by pouring washings into the final container d. Using cold distilled water to dilute a solution to mark so it does not get hot e. Using a volumetric pipette when applicable to get the most accurate aliquot volume f. After diluting to around 90mL before the mark, transfer the solution into a beaker to cool down more efficiently. g. Storing everything in plastic containers as plastic is more inert than glass for most chemicals Note: Just answer, no explanation needed. Thanks
1. Suppose each pair below is mixed well. What comes out as the simplest example of liquid mixing?A. 12 M sulfuric acid solution and 12 M sodium hydroxide solutionB. water with 80% ethanolC. ethane with methaneD. acetic acid and water
Calculate the quantity of lime and soda required for softening one million litre of the following sample of water. If the purities of lime and soda are 80% and 85% respectively. The impurities are Silica mg/lit. CaSO4 = 68 mg/lit. MgCO3 = 884 mg/lit. CaCO3 = 120 mg/lit. 75 mg/lit. MgCl2 = 19 mg/lit. MgSO4 = 30 %3D %3D
SHOW SOLUTION. The boiling point rise of a 30%-wt NaCI aqueous solution at 1 atm is ______.a. 20°F b. 5°F c. 45°F d. 30°F
3. Take another 10mL of the temporary hard water and boil for 5 minutes. Filter, then add 5 mL of soap solution to the filtrate and shake. What is the result? Is the water hard? Why is this type of harness called "temporary hardness"? What other substances cause temporary hardness? Write the equation for removal of temporary hardness by heating. Give 3 other methods of removing temporary hardness in water.
Are Particles Visible? Can it be Filtered? Do Partices Settie? See Tyndal Effect? Example Mixture Solution No saltwater Colloid No Suspension Yes Part 3 Separating Mixtures 15. Since the parts of a moture are combined, they can be separated rather easily. 16. F in the table below to sutmarize the 6 different separation techniques described. Technique Description Separates larger solids from smaller solids by passing them through mesh. Separates magnetic from non-magnetic materials Separates an insolluble solid from a liquid by passing it through a filter. Separates a soluble sold from a liquid by boling off the liquid. Separates a liquid from a soluble solid in solution by boiling and cooling it. Separates mitures of liquids with different boiling points using a condenser. Separates matures of liquids with afferent solubilities using absorbent paper. Part 4 Properties.of Matter 17. Matter can be described by 2 types of properties: and properties 18. A) s a property of matter one can…
How many milliliters of a 17% w/v concentrate of benzalkonium chloride should be used in preparing 150 mL of a stock solution such that 15 mL. diluted to 1 liter will yield a 1:5000 solution? A. 2 ml. B. 23.5 mL C. 11.75 ml. D. 0.2 mL
Why do two layers form when solutions containing water are added to the extracted dichloromethane (CH2CI-2) solution?