3. A mixture of 0.30 mole fraction benzene and the rest toluene is fed to a continuous distillation column to give an overhead product of 0.90 mole fraction benzene and a bottom product of 0.95 mole fraction toluene. The feed enters at 283 K with a specific heat capacity (Cp) of 1.84 kJ/kg K and a boiling point of 374.7 K. The latent heat of vaporisation (2) of the feed is 30 MJ/kmol. If the reflux ratio is 5.0, a. How many theoretical plates are required? b. How many actual plates are required assuming a plate efficiency of 80 percent? (Mwbenzene = 78 kg/kmol ; Mwrotuene = 92 kg/kmol) Equilibrium curve for benzene/toluene system is provided below.

Q: Write brief comments, with equations where appropriate, on the following   i. Constant Pressure filt...

A: The following basic concepts are to explained with relevant equations.   i. Constant Pressure filtra...

Q: What are the key assumptions in the evaporator model?

A: The key assumptions in the evaporator model are to be mentioned.

Q: a. 2000 kg/h of milk is sterilized in a steam infusion sterilizer. The milk is heated to 145 °C by i...

A: Let milk be represented as ‘M’ and steam by ‘S’. Assumptions are stated as:   Neglect any change in...

Q: Consider a binary liquid mixture for which the excess Gibbs energy is given by GEIRT = Ax1x2 (x1 + 2...

A: It is given that the excess Gibbs energy for a binary liquid mixture is given by,

Q: 5

A:

Q: What is meant by ion exchange? How does ion exchange differ from deionization?

A: Ion exchange is a process that is used to purify the solution by exchanging the unwanted ions by des...

Q: What is the analogical reason between heat transfer by conduction and flow of electricity through oh...

A: The diagram for the composite wall with conductivity ‘k’, thickness ‘t’, and cross-sectional area ‘A...

Q: Air is used to dry a solid wet with toluene at 1 atm. At a location where the air has a temperature ...

A: The humidity, the adiabatic-saturation temperature and the wet-bulb temperature for the Air-toluene ...

Q: A meat processing factory’s raw effluent has a five day BOD at 20oC of 1760 mg/l. If the k value is ...

A: Given data:   Five day BOD = 1760 mg/L The value of k = 0.15/day Temperature = 20 0C

Q: (b) Also, why is n/V squared in the van der Waals equation?

A: (b)   Van der Waals equation of states is defined as:

Q: Explain the PVT behavior of pure substances with appropriate examples  500 words

A: The substance whose compositions does not change gradually and are fixed throughout the process are ...

Q: Q4) A band from a column eluted at 0.66 mL/min has a width at half-height, w1/2, of 39.6 s. The samp...

A:

Q: What is freeze-drying and when is it a good choice?

A: The definition of the freeze drying and its applications is to be mentioned.

Q: Thermodynamics Question   Calculate the change in enthalpy and entropy when H2S is compressed from a...

A: Given information:   Gas compressed is H2S. Initial temperature of the gas, T1 = 137.2°C = 410.35 K ...

Q: 1. As we know Rain from sky follows Rain cycle, similarly So2 emission and absorption also follows a...

A: The sulphur dioxide cycle is to be explained.

Q: What is the difference between mother liquor and magma?

A: Mother liquid is the residual liquid after the separation processes from which the main component is...

Q: A reactive chemical disposed of by dilution dissipates at a uniform rate of 0.15mg/l per hour.The wa...

A: The distance down stream that the chemical residue persists is to be calculated.

Q: error_outlineHomework solutions you need when you need them. Subscribe now.arrow_forward   ...

A: (a)   The schematic diagram for the absorption of NH3 (A) in water (B) from the air in an enclosed t...

Q: In the 50 years following the development by Sorel in 1894 of a mathematical model for continuous, s...

A: The attributes of McCabe-Thiele  graphical method which makes it popular are to be mentioned.

Q: Book: Introduction to Chemical engineering Thermodynamics 8th edition, McGraw Hill, 2018

A: (a) The value of Margules parameter A is to be determined.   The modified Raoult's law is given as, ...

Q: Determine the fugacity and fugacity coefficient of ethane at 50 bar and 25 ºC using Less Kessler’s g...

A:

Q: Water is being discharged from the bottom outlet of a tank with certain area in cross-section. The d...

A: Given data: The diameter of the orifice = 40 mm or 0.04 m The water level in the tank is regulated b...

Q: Briefly explain an equilibrium stage operation and state the conditions needed to achieve this type ...

A: Separation process: Separations process is such process in which the solute (desired product) is sep...

Q: In a batch process, 100 lb of carbon monoxide gas are compressed adiabatically from 80°F and 15 psia...

A:

Q: A compressor receives air at 101.3 kPa at a steady rate of 0.5 kg/s and delivers at 700 kPa. At the ...

A: Given data: Initial pressure = 101.3 kPa. Mass flow rate = 0.5 kg/s. Final pressure = 700 kPa. Initi...

Q: A reactive chemical disposed of by dilution in a river dissipates at a uniform rate of 0.15 mg/l per...

A: The distance downstream that the chemical residual persists is to be determined.

Q: Why is chemical potential analogous to pressure and temprature

A: Chemical potential of any species is the measure of free energy i.e G of the species  And since the ...

Q: State the approximation of Fick's equation

A: Fick’s law is used to find the molar flux with respect to the observer moving with the molar average...

Q: It takes 20 seconds to fill a two-liter bottle with water from your kitchen faucet. What is the mass...

A: Given : The volume of the water bottle is 2 L  And the time required to fill the water is 20 s  

Q: An adiabatic steam turbine in an electric power plant is designed to accept steam at 5000 kPa and 60...

A: The inlet pressure of the steam to the adiabatic electric turbine is, P1 = 5000 kPa The inlet temper...

Q: Use material balance based on species method to calculate the products from reactor, where the two f...

A:

Q: Three fixed-bed adsorbers containing 10,000 lb of granules of activated carbon (ρb =30 lb/ft3 ) each...

A: Given information:   3 fixed-bed adsorbers Mass of activated carbon granules in each bed, m = 10,00...

Q: Why is maintaining constant supersaturation important during bioproduct crystallization?

A: The reason for maintaining constant supersaturation during bio-product crystallization is to be ment...

Q: 2.19 A steam-jet ejector is used to entrain saturated water vapour at 25 kPa (H = 2618.2 kJ/kg) leav...

A: The basis of the calculation is taken as 1 kg of the high-pressure steam fed to the steam-jet ejecto...

Q: At a particular location in a countercurrent stripper for the removal of solute A from a liquid stre...

A: (a) The interfacial composition is to be determined.   The liquid phase resistance is related to mol...

Q: How to solve this?

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question...

Q: A pump which supplies water at the rate of 200 cubic metre per hour is driven by a20-kWh electric mo...

A: The basis of the calculation is taken as 1 hour.   Power of the electric motor is given as P = 20 kW...

Q: A force that will accelerate 1 slug of mass at a rate of  1ft/s2 is known as a   a. Newton. ...

A: The correct option for the relation between slug and acceleration is to be chosen.

Q: 10 kg of C7H16 is burned with 6.8027k-mol of air. To produce 14.4 kg of CO2 along with other combust...

A: (a)   ‘i’ represents initial mass and moles, ‘f’’ represents final mass and moles, ‘m’ represents th...

Q: It takes 15 kWh (kilowatt-hours) of electrical energy to produce 1.0 kg aluminum metal from aluminum...

A: NOTE : 1 Watt = 1 J/s and not 51 J/s  And 1 KWh = 3600 KJ  

Q: What is the approximation of Fick's equation(Hint: the first three terms)

A: The approximation of Fick’s law are as follows: Flux should be considered in only one dimension tha...

Q: Chemical Engineering Question

A:

Q: Distinguish between carnot heat engine and refrigerator

A: Carnot heat engine is a theoretical engine which operates between two temperatures on a Carnot cycle...

Q: 1.1 The number of molecules crossing a unit area per unit time in one direction is given by N =-no w...

A: Given information:   The gas is at standard conditions. The average molecular velocity is taken appr...

Q: Sketch the principle of a hydraulic press. Explain the principle of the amplification of the force. ...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: An explanation would be helpful!

A: The given system of two flasks connected to each other by a tube is at the temperature of 45°C. Flas...

Q: Lesco Chemical is considering two processes for making a cationic polymer. Process A has a first cos...

A:

Q: Q1: Aluminium sulfate is used water treatment and in many chemical processes. It can be madeby rcact...

A:

Q: A number of polymers, including polyvinylchloride, polystyrene, and polymethylmethacrylate, are made...

A: The reason for rotary dryers, fluidized-bed dryers and sprouted dryers are good choices for polymer ...

Reactive Processes

Reactive processes are the processes in which any reaction occurs. The reactions can be any combination reaction, decomposition reaction, combustion reaction, oxidation reaction, reduction reaction, neutralization reaction, displacement reaction, or double displacement reaction.