25 ml of 1M HCI la0) at 23.4°C was added to 25 ml of 1M NAOH at 23.4'C. The final temperature of the reaction mixture was 29.7 C. Calculate A H (KJ/mol). Density of each solution is 1.04 g/ml and Specific heat of water =4.184 J/g."C

25 ml of 1M HCI la0) at 23.4°C was added to 25 ml of 1M NAOH at 23.4'C. The final temperature of the reaction mixture was 29.7 C. Calculate A H (KJ/mol). Density of each solution is 1.04 g/ml and Specific heat of water =4.184 J/g."C

Introduction to General, Organic and Biochemistry

11th Edition

ISBN:9781285869759

Author:Frederick A. Bettelheim, William H. Brown, Mary K. Campbell, Shawn O. Farrell, Omar Torres

Publisher:Frederick A. Bettelheim, William H. Brown, Mary K. Campbell, Shawn O. Farrell, Omar Torres

Chapter5: Gases, Liquids, And Solids

Section: Chapter Questions

Problem 5.58P

See similar textbooks

Related questions

Q: Question 6

A: For the given process, the heat change may be calculated as:

Q: 8. If the accepted value for the heat of solution for NH,NO, is 25.69 kJ/mol, calculate the percent…

A: Molar enthalpy of solution is the amount of heat released or absorbed per mole of a substance. It is…

Q: For the reaction Na₂CO3 + 2HCl-NaCl + CO₂ + H₂O ΔH is -144.1 kJ. What is ΔU

Q: What is ∆G° for the reaction CaO(s) + CO₂(g) → CaCO₃(s)?

Q: A tablespoon (about 15.0 mL) of sodium chloride, a common table salt, is dissolved in water. What is…

A: Given :- Volume = 15ml density of NaCl = 2.16 g/cm3 Delta H = 3.87 KJ/mol

Q: Calculate the Enthalpy of change in Kj/mol and % difference in the neutralization reaction below:…

A: Given neutralization reaction:

Q: In the following experiment, a coffee-cup calorimeter containing 100.0 mL of H2O is used. The…

A: The heat capacity is the ratio of the energy supplied in the form of heat to the rise in the…

Q: olution is formed when the solute uniformly disperses oughout (or dissolves in) the solvent. The…

A: The process which absorbs energy is known as endothermic process and the process which release…

Q: If a student determined that the enthalpy of solution in kJ was -3.15 kJ and they used 0.045 mol of…

Q: A student followed the procedure in this experiment, using 28.0 mL of 1.55 molar HCl and 31.0 mL of…

Q: . Find the maximum possible temperature that may bereached when 0.050 mol Ca(OH)2(s) is allowed to…

A: Number of moles of strong acid HCl = 1 mol Number of moles of strong base Ca(OH)2 = 0.05 mol 1 mol…

Q: 0.700 moles of an unknown solid is placed into water to make 150.0 mL of solution. The solution's…

A: The amount of heat required to increase the temperature of one kilo gram of a substance by one…

Q: 3.15 mol of an unknown solid is placed into enough water to make 150.0 mL of solution. The…

A: Answer :- Below I have explained step by step complete solution . Hope this will really gonna help…

Q: 6.41 g of MgSO₄ is placed into 100.0 mL of water. The water's temperature increases by 6.70°C.…

Q: Mass of calorimeter + water is 52.0753g, mass of water is 44.34g, mass of Unknown Solid is 5.00g,…

Q: The salt barium bromide is soluble in water. When 9.82 g BaBr2 is dissolved in 115.00 g water, the…

A: Given, The amount of water = 115.00 g Temperature (T1) = 250C Temperature (T2) = 26.680C. ∆t =…

Q: A 5.00 g sample of an unknown salt is dissolved in 50.0 mL of water. During dissolution, the…

A: The question is based on the concept of chemical thermodynamics. we have to to identify heat change…

Q: When 30.0 mL of 0.400 M Ca(NO3)2 is added to 30.0 mL of 0.800 M NaF, CaF2 precipitates, as shown in…

A: Given : Volume of Ca(NO3)2 = 30.0 ml Molar concentration of Ca(NO3)2 = 0.400 M Volume of NaF =…

Q: 6.Write the equation for the standard formation of one mole of HF(g) from the pure elements.

Q: Given the reaction NaOH(aq) + HCl(aq) -> NaCl(aq) + H2O(l), find the enthalpy of reaction. NaOH:…

Q: When 3.00 g of sodium hydroxide (NaOH) was dissolved in 150.00 g of water a value of 11.00oC was…

A: The heat of the solution produced when 3.0 g of sodium hydroxide is dissolved in 100 g of water, is…

Q: 60.0 mL of pure water at 282 K is mixed with 100.0 mL of pure water at 339 K. What is the final…

A: just apply , Heat given = Heat taken

Q: ENTHALPY OF REACTION for THREE REACTIONS 1.9886 g 2.0193g 1. Mass of solid NaOH(g) Record M and V…

A: The amount of heat required to raise the temperature of the sample is given by: q = mC∆Twhere q is…

Q: 10.01 g of MgSO₄ is placed into 100.0 mL of water. The water's temperature increases by 6.70°C.…

A: Given data: 10.01 g of MgSO₄ 100.0 mL of water density of the water is 1.00 g/mL specific heat of…

Q: 7.46 g of ammonium persulfate is dissolved in 112.0 mL of water. Initially the temperature of the…

Q: 0.700 moles of an unknown solid is placed into water to make 150.0 mL of solution. The solution's…

Q: precipitation reaction. A 50.0 ml. solution of 0.330 M AGNO, was mixed with 50.0 ml. of 0.170 M KI.…

A: From the given data we haveTotal volume of solution=50+50=100mldensity of the solutions=1g/mLSo…

Q: The change in enthalpy for the reaction A → P is x kJ/mol. What does the enthalpy change for the…

A: The negative sign of enthalpy in a reaction indicates that it is exothermic. If sign of ∆H is…

Q: 18.61 g of MgSO₄ is placed into 100.0 mL of water. The water's temperature increases by 6.70°C.…

A: The heat evolved in the dissolution of MgSO4 is being used by the solution to rise its temperature.…

Q: 50.0 mL of 0.10 M HCl is mixed with 50.0 mL of 0.10 M NaOH. The solution temperature rises by 3.0…

A: Given: Concentration of HCl =0.10 M Volume of HCl =50.0 mL Concentration of NaOH =0.10 M Volume of…

Q: 3.15 mol of an unknown solid is placed into enough water to make 150.0 mL of solution. The…

A: To calculate the mass of solution q = ∆H = mC∆T q = ∆H = heat = ? m = mass = 150.0 ml x 1.20 g/ml =…

Q: A manufacturer accidentally produces their cold packs using the salt ammonium chloride (ΔH = 0.274…

A: Cold packs are the substance which are used to provide cool sensation wherever needed. So we would…

Q: 3.61 g of MgSO₄ is placed into 100.0 mL of water. The water's temperature increases by 6.70°C.…

Q: 0.700 moles of an unknown solid is placed into water to make 150.0 mL of solution. The solution's…

A: Density of solution = 1.02 g/mL Number of moles of unknown solid = 0.700 moles Volume of solution =…

Q: Calculate the Enthalpy of change in Kj/mol and % difference in the neutralization reaction below:…

A: The balanced neutralization reaction is: HNO2(aq) + NH3(aq) ----> N2(g) + 2H2O(l) ; ∆Hrxn = -…

Q: ute solution of hydrochloric acid with a mass of 606.87 g and containing 0.31625 mol of HCl was…

Q: From the reaction below, determine the amount of heat involved by mixing 10.0 g of CaC2 (molar mass:…

Q: Using the provided table, determine the molar enthalpy (in kJ/mol) for the reaction 2 K(s) + 2…

Q: calculate the standard enthalpy change (in kJ/mol) for each of the following reactions. (a) 2 Na(s)…

A: Standard enthalpy of a reaction can be calculated by subtracting the sum of standard enthalpies of…

Q: Consider the molar enthalpy change for this neutralization reaction:…

Q: A student determines the heat of dissolution of solid cobalt(II) sulfate using a coffee-cup…

A: Given the mass of water inside the coffee-cup calorimeter = 101.00 g Mass of the solute, CoSO4(s)…

Q: 5.21 g of MgSO₄ is placed into 100.0 mL of water. The water's temperature increases by 6.70°C.…

A: In order to increase one unit temperature of a substance, the amount of energy supplied in the form…

Q: A student followed the procedure in this experiment, using 29.5 mL of 1.59 molar HCl and 31.0 mL of…

Q: The salt sodium perchlorate is soluble in water. When 8.44 g of NaClO4 is dissolved in 104.00 g of…

A: Given that : Mass of NaClO4 (mn)= 8.44 g Mass of water (mw) = 104.00 g Change in temperature ∆T=…

Q: 5.21 g of MgSO₄ is placed into 100.0 mL of water. The water's temperature increases by 6.70°C.…

A: The enthalpy change during dissolution is equal to the heat absorbed by the solution.…

Q: Calculate enthalpy of reaction given reaction enthalpies for proposed steps in a process. K+(g) +…

Q: Table 4. Enthalpy of solution of salts data and calculations NHẠNO3 MgSO4 [1] Mass of salt (g) 2.001…

Q: 3. Are Kp and Kc the same thing? What units are generally associated with them and why? Give an…

A: The question is based on the concept of equilibrium. we need to describe about different EQUILIBRIUM…

Q: 5.61 g of MgSO₄ is placed into 100.0 mL of water. The water's temperature increases by 6.70°C.…

A: To increase one unit of temperature of a subsyance. The amount of energy supplied in the form of…

Q: 50.0 mL of 1.00 M HCl is mixed with 50.0 mL of 0.95 M KOH in a calorimeter with a caloriemeter…

A: Given: 50 ml of 1 M HCl. 50 ml of 0.95 M KOH Calorimeter constant: 17.3 J/C Specific heat capacity:…

Concept explainers

Solutions

Solutions can be considered as homogeneous mixtures which contain two or more than two chemical substances. The chemical substance which is the greater part is defined as solvent. And the chemical substance that is dissolved in a solvent is referred to as solute. Solution chemistry plays an important role in chemistry since it supports many commercial applications of solutions.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

The air in a recently used classroom 9m x 7m x 9m tested 0.12% carbon dioxide. How many cubic meters of fresh air must be admitted per minute in order that 10 minutes later it shall contain not over 0.06% carbon dioxide. Fresh air contains 0.04% carbon dioxide. Assumeimmediate mixing of fresh with stale air. (A) 14 (B) 11 (C) 15 (D) 19 (E) 17
احسب مولارية المحلول 0.9gm/500ml/NaoH/Na=23/0=16/H3D1
These organic solvents are used to clean compact discs:(a) If a 15.00-mL sample of CD cleaner weighs 11.775 g at 20C, which solvent is most likely to be present?(b) The chemist analyzing the cleaner calibrates her equipment and finds that the pipet is accurate to 0.02 mL, and the balance is accurate to 0.003 g. Is this equipment precise enough to dis-tinguish between ethanol and isopropanol?
26) The floor tiles in SE 27 are about 1 square foot and the lab is about 25 tiles wide and about 36 tiles from front to back. When the emergency shower was demonstrated, in 10. seconds the water in the trash can was about 1 foot deep. One student estimated this was 2.5 gallons. Estimate how deep the room will get in inches after a 15 minute shower. List 3 simplifving assumptions you make in this calculation rea L-36 Tile fiDw ill it cost2 The density of gold is 27l An artist plans to apply gold leaf to a painting with an area of 2.32 f? and a thickness of 1.50
60°F Cloudy Aktiv Chemistry C KU Portal < https://app.101edu.co D2L E Ch 1 Introduction... Aktiv Chemistry || | || || ||| Connect-Big Google Docs CB Grade Calculator L R Point Grade Calcula... Question 22 of 25 If 70.0 grams of carbonic acid are sealed in a 2.00 L soda bottle at room temperature (298.15 K) and decompose completely via the equation below, what would be the final pressure of carbon dioxide (in atm) assuming it had the full 2.00 L in which to expand? H₂CO3(aq) → H₂O(l) + CO₂(g) Class Search How to St
2.) It’s a bad day in the lab! Two students are doing experiments. Each is 20 feet away from the professor. At the same time, each of them lets the same amount of a smelly gas into the room. One of them releases ammonia, NH3, and the other releases SO2. NH3 has a pungent odor, and SO2 smells like rotten eggs. The professor has no idea that this has happened, until she smell the first gas. Which chemical will the professor smell first? (NH3 or SO2) . If the professor starts to smell the first gas 42. seconds after the gas is released, how long will it take her to smell the second gas? sec. * Note: It is unsafe practice to work with these chemicals in an open lab.
The student collected the following data he prepared solutions ranging from 0.000 to 0.500 ppm and measured the instrumental reading corresponding to each of the solutions prepared: Yi 0.000 0.00 0.100 12.36 0.200 24.83 0.300 35.91 0.400 48.79 0.500 60.42 Use the method of least squares to calculate the equation of the best straight line going through these points ii) Calculate the amount of unknown in your sample if the unknown reading is 40.35 ii) If blank standard deviation was 0.014. Calculate: 1. LOD,
Two groups did the Chem 16.1 Experiment 10 with exactly the same mass of Mg, temperature, and barometric pressure. Group X used a 50-mL eudiometer while Group Y used a longer 100-mL eudiometer. After the experiment, both groups observed a Case A scenario. Additionally, they noted that the group using the longer eudiometer recorded a higher h. How would the volume readings in their eudiometers compare? a. Group X < Group Y b. Group X = Group Y c. Indeterminate d. Group X > Group Y
1) Listen -5 The Ksp value for calcium sulfate [CaSO4] is 2.40 X 10 and a professor made 1825 mL of a CaSO4(ag) solution but then one of his graduate student accidentally poured in a 0.125 M solution of calcium phosphate [Cag(PO4)2] solution. You may ignore the additional volume coming from the Ca3(PO4)2 solution to make the calculation simpler. Calculate the new sulfate (SO42) ion concentration at equilibrium with this common ion effect. 6.40 x 10-5 5.25 x 10-5 6.21 x 10-5 5.44 x 10-5 201591..docx LAB EXP. #3 -..docx Show All
Consider the following data: HX → X- + H+ Ką = 6.61 · 10- 5 H2A + НА + Н + Ka = 2.68 · 10-7 Calculate the Keg for the following reaction: H2A + X¯ + HA¯ +HX Record your answer in scientific notation to 3 sig figs.
3.1524 g HCI (FW 36.46) was diluted with 45 mL water and titrated with 1.0149 M NAOH (FW 40) using methyl red as indicator. 28.02 mL of NAOH was required to neutralize the HCI. Calculate the percentage w/w of HC. Record your answer in decimal notation to 2 decimal places. Answer = % w/w %3D
/view.php?id%313481845 Dogle YouTube home Wells Fargo - Pers.. A American Express... E Google Docs h Stream TV and earning University of Nevada, Las Vegas - CHEM 122 - Fall20 - ORGILL > Activities and Due Dates > HW 5 t Score: 92.2% > [OH-] =0.186 x10-5 РОН 3D| 5.73 Determine the H*], OH-, and pH of a solution with a pOH of 13.61 at 25 °C. [H*] = %3D [OH-] = 0.245 x10¬13 pH = about us careers privacy policy terms of use contact us help 9. MacBook Pro