20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 890 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the actual change of volume in final plate. Provide the answer in mm³ a with two decimal points of accuracy. σ = 80 MPa 20 mm Answer: D 20 mm B σ = 160 MPa C

20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 890 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the actual change of volume in final plate. Provide the answer in mm³ a with two decimal points of accuracy. σ = 80 MPa 20 mm Answer: D 20 mm B σ = 160 MPa C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm C B V 100MPa -200 MPa E-80GPa ✓=0.3 G=30MPa
200KN A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of each material are shown in the figure. A fixed support is rigidly attached to the right end of the bronze rod. Determine the stress each section in kPa. Aluminum Steel D=28mm D=20mm 20KN Bronze D=25mm 150KN
7. A cylindrical steel bar is subjected to repeated compression-tension stress cycling along its axis. The mean stress is zero (0). If the maximum tensile load applied to the bar is 15,000 N, calculate the minimum allowable bar diameter (in mm) to ensure that fatigue failure will not occur. Assume a Safety Factor of 3. Show all work (4). 500 450 400 S 350 300 250 103 104 105 106 107 108 S (MPa)
20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the final thickness. Provide the answer in mm a with two decimal points of accuracy. σ = 80 MPa 20 mm Answer: D 20 mm σ = 160 MPa
Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle D if the pull on the handle is slowly increased and reaches the magnitude of P = 655 lb. o (ksi) 40 pulg 80 70 B 50 pulg - 30 pulg € (pulg/pulg) 0.007 0.12
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in bronze bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 144.21 102.49 341.33 54.56
A circle of diameter d = 225 mm is inscribed on an unstressed aluminum plate of thickness t = 18 mm. Forces acting in the plane of the plate later cause normal stresses o₂ = 84 MPa and o₂ = 140 MPa For E= 70 GPa and v=- (v = poisson's ratio), determine the change in y D Listah 380 mm A C 0₁ 380 mm B (i) The length of diameter AB, (ii) The length of diameter CD, (iii) The thickness of the plate, x
Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 °C. Use the following data: A (mm?) a (C) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10- 70 Copper unusunjv Copper 750 mm-
Determine the following for the bar. A) B) C) D) σ, ksi 100 ksi 80 ksi T, ksi 40 ksi What is the Modulus of Elasticity for the material of the bar. What tensile force will cause the bar to yield? What will be the length of the bar after a 540 kip force is applied? What will be the cross sectional dimensions after a 300 kip force is applied? 0.0025 0.0035 0.0095 0.0100 0.0130 0.0145 Y, radians ɛ, in/in 20 in 3 in Cross Section 2 in
a = 450 mm t = 20 mm Op b= 350 mm The plate shown in the figure is made of a material having a modulus of elasticity of 200 GPa and Poisson's ratio of 0.2. The plate is under the effect of normal stresses oą and op. The magnitude of oą is 150 MPa. If the final thickness of the plate is known to be 20.001 mm under the applied stresess; determine the magnitude of op. Express your answer in MPa and round it to the nearest integer if necessary.