2. Based on the pressure of fluid on the submerged curved or flat plate, hydraulic gates are commonly used in many fluid-related engineering practices. Figure 2 shows a gate under water, where a = 45°, y₁ = (5+ 40) cm, and y2 = 4 m. (a) Will the gate fall or stay in position under the action of the hydrostatic and gravity forces if the gate itself weighs 150 kN and is 1.0 m wide (towards the paper)? Use calculations to justify your answer. (b) Discuss how the gate will be stay or open if the angle of the gate is increased or decreased further to a certain value.

2. Based on the pressure of fluid on the submerged curved or flat plate, hydraulic gates are commonly used in many fluid-related engineering practices. Figure 2 shows a gate under water, where a = 45°, y₁ = (5+ 40) cm, and y2 = 4 m. (a) Will the gate fall or stay in position under the action of the hydrostatic and gravity forces if the gate itself weighs 150 kN and is 1.0 m wide (towards the paper)? Use calculations to justify your answer. (b) Discuss how the gate will be stay or open if the angle of the gate is increased or decreased further to a certain value.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude of the hydrostatic force acting on the gate using the HYDROSTATIC PANEL EQUATIONS. Express your answer in kips. B. Determine the minimum force P required to open the seawater gate. Express your answer in kips.
A vat full of paint (SG = 0.80) is 8 m long and 4 m deep and has a trapezoidal cross section 3 m wide at the bottom and 5 m wide at the top as shown. Compute the force on the bottom of the vat. 5 m 1m4 4m 8m 3m Fig. 3-17 Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kN Decimal Places required in the final answer: 3
The 0.5-m radius semi-circular gate shown in the figure is hinged through the top edge AB. Find the required force to be applied at the center of gravity to keep the gate closed. B= 80kPa (abs) 4.74m Oil SG = 0.91 R Glycenn SG = 1.26
QUESTION 2 The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 20 mm. If a force of 50 kN is applied to the bar as shown in figure, determine the vertical displacement of the load. 0.9 m 0.6 m B D -0.375 mo.225 m 0.3 m F 50 kN
SOLVE FOR THE FOLLOWING USING PRESSURE-PRISM METHOD 2. The gate shown is rectangular and has dimensions 6 m by 4 m. What is the 3 m Hinge Atmospheric reaction at point A? Neglect the weight of the gate. pressure Stop /30 6 m Water
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
SOLVE FOR THE FOLLOWING USING PRESSURE-PRISM METHOD 1. A tank is filled to a depth of 5 feet of water and is 8 wide by 10 feet long. Determine the hydrostatic force acting on the horizontal bottom and on the vertical ends of the tank. 2. The gate shown is rectangular and has dimensions 6 m by 4 m. What is the 3 m Hinge reaction at point A? Neglect the weight of the gate. Atmospheric pressure Stop 30 6 m Water
As shown in the figure compute the amount and location of the vertical and horizontal components of the hydrostatic pressure on XY QUADRANT OF CIRCLE 5M WIDE 2.75H RADIUS i DETERMINE ALSO FORCE "F" TO PREVENT ROTATION F PV Y yW.S PH HINGE
1. Figure shows the side view of a tank with a curved gate. The gate width into the page is 18 in. The tank contains turpentine and is filled to a depth of 32 in. (a) Determine the magnitude (in Ib) and direction (R or L) of the horizontal component of the force acting on the curved gate. PLS DRAW DIAGRAM (b) Determine the magnitude (in Ib) and direction (U or D) of the total vertical component of the force acting on the curved gate. DRAW DIAGRAM PLS (c) Determine the magnitude of the total force (in Ib) acting on the gate. (d) Determine the angle that the total force acting on the gate makes with the horizontal.
Given: The figure shown below Find: The moment about pipe segment AB caused by the force vector F _3 ft' 4 ft Solution: 4 ft' - 2 ft B F = {30i – 45j + 50k} lb 4 ft
Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force (P) is required at point B for equilibrium. The weight of the gate is negligible, and C = 5 m J = 4 m E = 2 m O= 60° S.G. of Oil = 0.82 Oil, SG = 0.82 E Gate * Q1- Determine the magnitude of the force acting on the gate due to oil pressure Q2- What is the moment of inertia of point *? the given triangular gate Q3- Determine the vertical depth of the center of oil pressure from the *. Free surface Q4- Determine the horizontal force (* .P) required for equilibrium Q5- If the shape of the gate is square with the dimensions of 3 mx 3 m, determine the .magnitude the force acting on the gate due to oil D
Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force ( P) is required at point B for equilibrium. The weight of the gate is negligible, and C = 2 m J 5 m E = 1.2 m 9 = 60° %3D S.G. of Oil = 0.82 Oil, SG = 0 82 %3D Gate J