2. A sign with dimensions of 2.0 m x 1.2 m is supported by a hollow circular pole having an outer diameter of 220 mm and an inner diameter of 180 mm. The sign is offset 0.5 m from the centerline of the pole, and its lower edge is 6.0 m above the ground. Determine the principal stresses and maximum shear stresses at points A and B at the base of the pole due to a wind pressure of 2.0 kPa against the sign. 0.5 m For hollow circular cross section: max B 11 VQ lb -2.0m MJT Bookstore A 180 mm 220 mm B 1.33- 1.2 m 6.0 m 3+ (²²2² +²₂2²₁ +²2²) 2 A

2. A sign with dimensions of 2.0 m x 1.2 m is supported by a hollow circular pole having an outer diameter of 220 mm and an inner diameter of 180 mm. The sign is offset 0.5 m from the centerline of the pole, and its lower edge is 6.0 m above the ground. Determine the principal stresses and maximum shear stresses at points A and B at the base of the pole due to a wind pressure of 2.0 kPa against the sign. 0.5 m For hollow circular cross section: max B 11 VQ lb -2.0m MJT Bookstore A 180 mm 220 mm B 1.33- 1.2 m 6.0 m 3+ (²²2² +²₂2²₁ +²2²) 2 A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A sign with dimensions of 2.0 m x 1.2 m is supported by a hollow circular pole having an outer diameter of 220 mm and an inner diameter of 180 mm. The sign is offset 0.5 m from the centerline of the pole, and its lower edge is 6.0 m above the ground. Determine the principal stresses and maximum shear stresses at points A and B at the base of the pole due to a wind pressure of 2.0 kPa against the sign. 0.5 m For hollow circular cross section: max B 11 VQ lb -2.0m MJT Bookstore A 180 mm 220 mm B 1.2 m 6.0 m V -1.33 (2²+5+4² A
For the section shown, if d = 200 mm, horizontal shear force = 100 kN to the right and torque = 15 kN.m clockwise, then the total shear stress at point B is …..... A B E 13.79 MPa downward O 13.79 MPa to the right O zero 9.55 MPa downward 9.55 MPa to the right O
3) The overhanging beam supports the loads as shown in the figure. Determine the maximum shear stress in the beam 60 kN/m 20 kN/m 0.1m 0.3m B .C 3m 2m 2m D 0.25m
Consider a circular beam 8 m long and 600 mm in diameter subjected to uniformly distributed load of 30 kN/m as shown in figure. 150 mm 2 m 30 kN/m 6 m B Direct shear stress developed at P will be 0.21 MPa. For analysis of point 'P' which is at AA' section, which of the following statements is/are correct? A Bending stress developed at P will be 4.24 MPa. C Maximum shear stress developed at P will be 4.26 MPa. OI D Maximum shear stress developed at P will be 2.13 MPa. 600 mm
The T section is shown in Figure below is the cross-section of a beam. The beam is subjected to a uniform distributed load = 4 kN/m. The N.A is located at 34.7 mm from the bottom and that IxA =10.64x106 mm. Determine (a) the maximum shearing suess (b) the shearing stress at 15 mm from the bottom face. Q2 %3D 20mm 4 kN/m 120mm A 34.7 mm 20mm lm 3m 1m 220mm TT
Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-section is square, 0.45 in. on each side. Draw free-body diagram.
The bar has a 140 mm by 20 mm rectangular cross section. If P = 190 kN, determine the force components perpendicular (N) and parallel (V) to a-a, the inclined surface area, and the normal and shear stress magnitudes acting on surface a-a.
2. s) The sign is subjected to the uniform wind loading. Determine the stress components at points A and B on the 100-mm-diameter supporting post. Show the results on a volume element located at each of these points. 4 3 m 2 m 2m 1.5 kPa B C 1m D
SITUATION 3. A hollow rod has an outside diameter of 125mm and inside diameter of 75mm is 3.2m long. G= 77 MPa allowable shear stress = 250 MPa 7. Find the maximum safe T a. 89.41 kN-m b. 52.91 kN-m c. 42.50 kN-m d. 83.45 kN-m 8. If the rod is subjected to a torque of 12.5 kN-m, find the minimum shear stress a. 27.42 MPa b. 15.92 m c. 24.59 m d. 22.47 m
A 2 kN compressive force subjected to a wooden rectangular block. Determine the average normal and shear stresses developed in the wooden block that are oriented along section a-a at 30°. |50 mm 150'mm 2 kN 2 kN 30
Calculate the average normal stress and the average shear stress on a plane passing horizontally through member AB'at a height of 1m from point A. Member AB has a square cross section of 30mm. w=12KN/m b - 3 m A 4 m
For the following 'shapes', compute the shearing stress at the horizontal neutral axis. Shear force = 104 kN