2) The samples x[k] of an analog signal x(t) is shown below in Fig. 1, x[nTs] 2 Ts 2T 3T Fig. 1 a) Express mathematically the reconstructed signal x(t) if a first-order-hold circuit is used with impulse response h(t) = A (7) where Ts is the sampling interval. b) Draw the reconstructed signal if the above first-order-hold circuit with impulse response h(t) is used.

2) The samples x[k] of an analog signal x(t) is shown below in Fig. 1, x[nTs] 2 Ts 2T 3T Fig. 1 a) Express mathematically the reconstructed signal x(t) if a first-order-hold circuit is used with impulse response h(t) = A (7) where Ts is the sampling interval. b) Draw the reconstructed signal if the above first-order-hold circuit with impulse response h(t) is used.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

QI: A discrete time signal x(n) is shown in figure, sketch the following signal a) x(-n-2) b) x(2-n)u(n) c) x(n)u(2-n)
1) y(t) = 3e-2tu(t)The function above defines the model of a signal from the braking activities of a vehicle.a)sketch the signal using the information above.b)Determine the power & energy of the signal. 2) A sensor is used to capture voltage signal y(t) from a volcanic eruption & passed through an active highpass filter system for processing.a)Make a circuit diagram sketch for the process.b) Derive an expression for the transfer function of the system. c)Cut-off frequency = 2.5kHz & Input voltage = 20mVUse the above data to determine the values of the circuit components needed to produce an output of five volts. d) Suppose a two volts input voltage is applied to the filter system, In terms of unit step function, i) what is the expression for this input? ii)Determine the output z(t) of the system. Assumption: All the circuit components in the transfer function equation have unity values.
1. A discrete-time signal is defined as: x(n) = { 1+ 1, b. x(4-n) c. x(n)u(2n) d. x(n-1)8(n-3) 0, n 3' a. Determine its values and sketch the signal x(n) b. Can u express the signal x(n) in term of signals 8(n) and u(n)? -3 ≤ n ≤-1 0≤n≤3 elsewhere 2. A discrete-time signal x(n) as shown in the figure below: x[n] IIII -2-1 0 1 2 3 4 Sketch and label each of the following signals: a. x(n-2) in matlab program solve
Solve All parts or will dislike answer A. Find the open-loop transfer function . Y(S) / R(S)B. Find ?(?) when the input ?(?) is a step function (use expansion of partial fractions).C. State the damping factor ?.D. Indicate whether the system is overdamped, underdamped, or critically damped.E. Indicate the natural frequency of the system ??.F. Indicate the poles and zeros of the system.G. Use the end theorem to find the steady-state value.H. Find ?(?) (use inverse Laplace transform).I. Plot the time response of the system.
Q1) Determine the transfer function and the block diagram of the following systems. Explain in detail the steps to follow to reach the result Consider that the input signal is ?i(?) and the output signal is ?c(t)
Problem 1. A signal x(t) with frequency as given below is passed through an ADC (Analog to Digital Converter) running at sampling rate Fs1 and a DAC (Digital to Analog Converter) operating at Fs2, What is the frequency of the reconstructed signal x’(t) ? (note the values of Fs1 and Fs2 are different between them and different for the different parts of the question) a. f1 in = 600 Hz; Fs1 = 1kHz; Fs2 = 2 kHz; b. f2 in = 750 Hz; Fs1 = c. f3 in = 400 Hz; Fs1 = d. f4 in = 200 Hz; Fs1 = x(t) fin ADC 1kHz; Fs2 = 4 kHz; 1kHz; Fs2 = 500 Hz; 1kHz; Fs2 = 1 kHz; f4 out = ? f1 out =? f2 out = ? f3 out = ? Fs1 DAC 2016dW FS2 x'(t) fout tenent Yes oldo19
Which signal-flow graph is adequate of the following block diagram? X(s). E(s) Y(s) H (s)
a) Find Tc,TS of -4 CSt(-4>) b.) Draw the time response
Chose a suitable range for n to depict the signal or sequence by calculate to prove the discrete signal; a)Impulse Signal b)Unit Step Sequence c)Exponential Sequence d)Sinusodial Sequence
The signal s(n)s(n) is recorded with frequency sampling Fs=500HzFs=500Hz. What's the duration of the following part s1(n)s1(n) of the signal s(n)s(n) where s1=s(601:4:5000)
"Time domain representation is an ac signal representation considers the time-varying nature of the signal, specifically its sinusoidal form." O True O False
Question 3: Consider the simple signal processing system shown in the figure. The sampling period of A/D and D/A converters are T= 5 ms and T1= 1 ms, respectively. Determine the output ya(t) of the system if the input is Xa(t) = 3cos100nt + 2 sin250xt (t in seconds) x.(t) A/D T x(n) D/A T1 Postfilter y.(t) The postfilter removes any frequency component above F/2.