2) An IIR digital low-pass filter is required to meet the following specifications: Passband ripple (or peak-to-peak ripple): ≤ 0.5 dB Passband edge: 1.2 kHz Stopband attenuation: ≥ 40 dB Stopband edge: 2 kHz Sample rate: 8 kHz Determine the required filter order for a) A digital Butterworth filter. b) A digital Chebyshev filter. c) A digital elliptic filter.

2) An IIR digital low-pass filter is required to meet the following specifications: Passband ripple (or peak-to-peak ripple): ≤ 0.5 dB Passband edge: 1.2 kHz Stopband attenuation: ≥ 40 dB Stopband edge: 2 kHz Sample rate: 8 kHz Determine the required filter order for a) A digital Butterworth filter. b) A digital Chebyshev filter. c) A digital elliptic filter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q)Design a Discrete Time Low Pass Filter for a signal. Butterworth Filter. Chebeyshev Filter The specifications are:(Voice Signal) 1) Passband Fp = 4 kHz, with 0.2 dB ripple; Stopband FS 4.5 kHz, with 45 dB ripple. Sampling Frequency Fs = 22 kHz. (Use For Both Filters). 2) passband ripple - 0.2 stopband ripple 45 passband frequency 1300 stopband frequency = 1500. sampling frequency=10000. (Chebeyshev Filter) 3) Passband ripple=0.5 stopband ripple 50 passband frequency 1200. stopband frequency = 2400 Sampling Frequency= 10000. (Butterworth filter)." 4)Choose your own Specifications
Define briefly the terms used in filter below, a) pass band b) attenuation band c) Cut off frequency (-3db frequency)
a) Design a digital bandpass Butterworth filter with the following specifications: Center frequency of 2.5 kHz. Passband bandwidth of 200 Hz and ripple of 3 dB. Lower stop frequency of 1.5 kHz, upper stop frequency of 3.5 kHz. Stopband attenuation of 15 dB. Sampling frequency of 8 kHz. (b) Realize the designed filter using direct form realizations.
Design and construct/draw a low-pass Butterworth filter with a roll-off of rate of -60 dB/decade and a cutoff frequency of 10 kHz.
2. a) Consider the circuit shown in figure 3. i) Determine what type of filter is shown in Figure 3 i) Calculate the corner or cutoff frequency. Take R = 4 k &, L= 2 H, and C= 1 uF. R Figure 3 b) Describe the possibility of building a second order filter with only resistors and capacitors? and design the cutoff frequency of second order filter for low pass filter (Expected: Describe the possibility , design the second order filter for low pass filter circuit and design the cutoff frequency as equation only).
Sketch a low pass filter circuit
1. Choose which basic filter response suit the signal output criteria in the figure 2. State your reason. 2. Sketch the basic filter response to suit the output citeria in Figure 2. (with labelling of passband, transition region and cut-off frequency). 3. Choose 1 type of filter if a flat pass-band gain response is required.
Draw the circuit diagrams of a first and a second order band pass filter and indicate its lower and upper cut off frequencies. Do the same for band stop filter. thanks in advance! ..
The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
Write Legibly. Design a single pole low pass filter with a gain of 10 in the passband and a 3dB frequency of 5kHz. The minimum resistance in the passband for this filter is to be of 10k-ohms. What is the value of C in nF and in two decimal places only.?
o) For the given filters and their connection descriptions below, find the resulting filter type and determine the cutoff frequency or frequencies. Assume all filters has a midband gain of 1. ( 20 Hz Low pass Filter ) * ( 100 Hz Low pass Filter ) = ( 20 Hz High pass Filter) * ( 100 Hz High pass Filter ) = . ( 20 Hz Low pass Filter ) + ( 100 Hz High pass Filter ) = ( 100 Hz Low pass Filter ) * ( 20 Hz High pass Filter ) =
A low pass filter is a. Passes the frequencies lower than the specified cut off frequency b. Rejects higher frequencies c. Is used to recover signal from sampled signal d. All of the above