710 mm710 mmAnswers:Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise.R= iNM = iSingle resultant force.d =i255 N120 NN.mmm Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force,determine the distance d below point A to its line of action.190 N710 mm710 mm710 mm255 NAnswers:Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise.R= iNM =Single resultant force.120 NN•m

The step wise solutions along with figures are given below.

Answered: 190 N 255 N 120 N 710 mm 710 mm 710 mm

Engineering

Civil Engineering

190 N 255 N 120 N 710 mm 710 mm 710 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What are three categories of waste that are managed in any society.

Q: A drainage canal in the shape of trapezoid with a bottom width of 2,3m and a side slope of 1…

Q: A steel column, pinned at both ends, has a restrained against lateral movement at its mid- buckling…

Q: Trial Head (mm) 55 Cx Theoretical Discharge (m³/s) 0.0011 Change in Volume (m³) 0.01 time (s) 8.84…

Q: a clay layer above the groundwater table. For the following variables, calculate and plot o, u, and…

Q: A soil sample has a unit weight of 18 KN/m^3, when oven-dried completely, the soil sample has a unit…

A: This question is from geotechnical Unit weight of file sample is 18 KN per metre cube and dried unit…

Q: Sleepers are........ attacked by vermin and able to accommodate any .gauge Steel Concrete O Wooden O

A: Sleepers are used to hold the rail at a fixed gauge and provide stability against the heavy rolling…

Q: A welded girder has loads applied to the top flange as shown in Figure 3A. The girder is supported…

A: fyf = 300MPa

Q: Question #8: A tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. x 0.6 in. cross…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: f structural connection, what are the forces allowed and the forces resisted by the structural…

A: The three most popular types of supports in beams and structures to connect them to their base are…

Q: Part A Determine the tension in cable AB for equilibrium. Suppose that F=650 N. (Figure 1) Express…

Q: 1. A block resting on a horizontal ground weighs 80 N and inclined force with a slope of 5V:12H is…

A: The given data is shown below: Weight=80NSlope=5V:12HVelocity=12m/sDistance=40mCoefficient of…

Q: = An equal-tangent crest vertical curve with a length L unknown, has an initial grade is G₁ +2.5%…

A: G1 = 2.5% G2 = -1%

Q: Atmospheric pressure is about 1.00 x 105 Pa on average. Convert the downward force of the air on a…

A: Given: Pressure , P = 1*105 Pa Area, A = 1.27 m² Required : Force (in lb)

Q: Distinguish between painting and electroplating in trying to minimize corrosion .

A: Electroplating and painting both are the methods of metal protection from corrosion . Both have…

Q: 7. A water treatment plant of 200 m³/ day uses an activated carbon, in columns, to reduce phenol…

A: Given, V = 200 m3/day or 200000 L/day Co = 130 mg/L Ce = 10 mg/L

Q: Determine the reactions of the beam using Force Method Analysis. Set A is fixed, B is roller and w=4…

A: Force method:- Method of consistent deformation.

Q: For a one story concrete structural system with height =4 m, if: spans along x= 6 m, spans along y=5…

A: To calculate mid-span reinforcement area of beam : To calculate mid-span reinforcement we have to…

Q: A fan is used to force air having a temperature of 20°C theough the 200 mm diameter galvanized sheet…

A: Given Data:D=200mm=0.2mL=150mQ=0.15m2/sf=0.023

Q: Solve the problem using Moment -Area Method Problem I. The beam has a loose fit built-in support at…

A: Given PL = 200KN total span = 4m E= 72Gpa

Q: 5.2kN-m 20 KN 2.5 in. 75KN Fig. 6a Fig. 7 7. The thin rectangular plate shown in Fig. 7 is uniformly…

Q: A soil sample has an initial unit weight of 16.7 Kilo-Newton per cubic meter with a saturation of 18…

Q: There are 16 beams in the second floor of a house with a typical width of 400mm and depth of 300mm…

A: There is typing error in question. Width is given 400mm and depth 300mm which can't be structurally…

Q: Determine the all internal moments. Assume the supports at A and C are rollers and B is a pin. El is…

Q: A cube of metal with a height of 5.25 meters on each side floats in water. The specific gravity of…

Q: Use Bemollis equation to estimate the upward force on an airplane's wing if the average flow speed…

Q: PROBLEM 1 A beam having a width of 300mm and a depth of 525mm carries a dead load of 19 kN/m…

A: Problem 1 Design of RCC beam: Solution: Given: B = 300 mm H = 525 mm DL = 19 kN/m LL = 28 kN/m L =…

Q: Determine the moments at all supports. 10 kN 12 kN•m A B 4 m 2EI 4 m 3EI 6 m 4 kN/m C

Q: A. Determine the required Magnitude and location from point B of the resultant of the Forces acting…

Q: Q2/ The simple supported beam ABC in Fig2. Carries a distributed load of maximum intensity wo over…

Q: Sleepers are.......... attacked by vermin and able to accommodate any .gauge Steel Concrete O Wooden…

Q: A 12 kips/ft 6 kips C D ↓—— 3'´`—————▬ 3º ———24 B hinge

Q: ind the vertical displa midspan of the beam s

Q: For the conditions show below, calculate the safety factor of the clay against bottom blow-up after…

Q: Determine the positive maximum vertical acceleration () d with oil

A: Acceleration: - It is defined as the rate at which velocity of body changes with respect to time in…

Q: Determine the moments at all supports. El is constant. Support A and C are fixed. Support B is…

Q: Centroid with respect to the x-axis.

A: Centroid: - It is defined as the point where arithmetic mean of all the points of object is…

Q: Find hydraulic radius 5 ft ㅗ - 10 ft -

A: Given data : The value of width of rectangular section b=10 ft The value of depth of water d=5 ft…

Q: Question 3 A compressive force of 45 kN acts parallel to the longitudinal axis of the I-section as…

Q: cular concrete culvert, but the depth changes depending on the weather (due to storms). The Manning…

A: We knowθ=cos-1(1-yr)θ=cos-1(1-3.54.12)θ=135.017°Area…

Q: A 10 m 10 kN/m B Problem 2 a. Location of Amax from A b. Dmax

A: Given A fixed beam Required Location of maximum deflection and maximum deflection value

Q: A drainage canal in the shape of trapezoid with a bottom width of 2.3m and a side slope of 1…

Q: -4 m -4 m B 100 KN 30° -4 m- -4 m-

Q: Sieve and Atterberg limits tests were made on a soil specimen and results are given below: Sieve No.…

A: Solution- The calculation is shown is shown in the table, Sieve No. Weight of soil, g Weight…

Q: (a) What pollutants that can be found in stormwater and what are the sources? (b) Design a circular…

A: Since you have asked multiple questions we will solve first for you, Solution- Stormwater has two…

Q: From the table, compute the absorption capacity (%) of sample II. From the table above, which of the…

A: Given Data:weight of saturated surface Dried sample= 2490Weight of Even dried = 2384

Q: In a hydraulic lift, the radil of the pistons are 1.46 cm and 10.0 cm. A car weighing W=10.0 kN is…

A: According to pascal's law pressure applied at any location in enclosed fluid will be transmitted…

Q: B. Determine the support reactions at A, C & D of the loaded beam. 150 KN 45KN/m B 1.0 m 3.0 m 1.50…

A: To Determine Reactions at support A,C,D. There is no horizontal force, hence no horizontal reaction…

Q: Areinforced concrete column contains longitudinal steel equal to 1 percent of net cross-sectional…

A: This question is related to the Design of RCC Structure.

Q: What do you understand the building ordinance?

A: Explanation- The buildings ordinance is a set of restrictions adopted by state or municipal…

Concept explainers

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.

Question

710 mm
710 mm
Answers:
Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise.
R= i
N
M = i
Single resultant force.
d =
i
255 N
120 N
N.m
mm

Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force,
determine the distance d below point A to its line of action.
190 N
710 mm
710 mm
710 mm
255 N
Answers:
Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise.
R= i
N
M =
Single resultant force.
120 N
N•m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Question 1

VIEW

Question 2

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 302-N force is applied at A as shown. |-100 mm→ 200 mm - D 125 mm 200 mm 25° Determine the moment of the force about D. (You must provide an answer before moving to the next part.) The moment of the force about D is |N-m O.
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
1.) The simple machine shown below has 2 parts connected via a pin at A. The gripping teeth at B exerts a normal force. EXTERNAL FORCES a) Draw each half of the machine. Label the external forces acting on each half (at A and B). b) If the machine has any 2-force members, identify them. c) Solve for the values of all forces at A and B. 80 N 200 mm 50° 30 mm B 80 N
120 N·m A 300 60° 200 B 400 E 60° 300 200 Dimensions in millimeters 600 N G F Determine the magnitude of the force (in N) of the y-component of the internal pin at E.
Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a body is zero, the body is said to be in (a) rotating condition (b) translation condition (c) equilibrium condition 2. Number of component of reaction at hinge support are (a) zero (b) one (c) two (d) three 3. The angle that the vector A "=2i+3j makes with y-axis is 4. If angle made by the force with y and z axes are 0,= 60° and 0₂ = 45° then 0x =. 5. Force is completely defined by its (a) magnitude (b) direction. (c) point of application (d) All of these (d) dynamic condition
SOLVE for components Fu and Fv. U 30° 40° F = 600 N V
The 742-N force is applied to the 117-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂=0.83 Hk = 0.59 Answer: F = i 28° N P = 742 N
Determine the force (written as a vector) which BC exerts on member AB (a) if the 800-N load is applied to the center of member AB, and (b) if the 800-N load is applied to the center of member BC. 800 N A 1.1 m 1.1 m B 32 L. Answer: (a) F -( i i+ i j)N (b) F-( i i+ i i) N
Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against the smooth slot in the triangular plate. 400 N 135 mm 145 mm- Answer: D= i E 70 mm 120 mm N
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
A force-couple system is acting on the frame as shown. Use A=80N, B=700N, C=150N, and M= 120N.m. The system is to be replaced with a single resultant force R. B 30° [Select] [Select] [Select] [Select] [Select] [Select] M 400 mm 200 mm 300 mm (a) Calculate the absolute value of the x-component of the resultant in N. (b) Calculate the absolute value of the y-component of the resultant in N. (c) Calculate the magnitude of resultant in N. (d) Calculate the angle that the resultant makes with the horizontal in degrees. (e) Calculate the absolute value of the x-intercept of the resultant's line of action in mm. (f) Calculate the absolute value of the y-intercept of the resultant's line of action in mm.
3- For the beam given in the figure, a- Draw the elastic curve by using the Mohr Method. Calculate the values of A, B, VC, ec by using the Mohr Method. b- A 2EI 3 m B 3EI C I1m] 60Nm