12)Among the following, which technique can be used for 3D deformation measurement purpose? Ruller Stereoscopic video imaging system O Dial gauge Straight edge set
Q: 1) discuss the methods of measurement and what is the accurate method 2) What is the micrometer .and…
A: The comparison of the standard and the unknown amount yields the measurement. In other words,…
Q: What is a transfer-type measuring tool?
A: Precision measurements are those with an accuracy of 0.5 mm or 1°. These measurements are necessary…
Q: hich of the following statement is correct? The random errors can be minimized using: 1. Shielding…
A: Correct answer : 3. Statistical analysis of measured data
Q: The company produced a new product intended to measure diameter profiles. In a run test conducted,…
A: 1). Precision- option B is correct Accuracy is how close or far off a given set of measurements are…
Q: A Profilometer is used to measure: How hard a part surface is. How round a part is to…
A:
Q: Distinguish between “interference fit” and “Clearance fit”.
A: Clearance fit- It occurs when two tolerance parts will always leave a space or clearance when…
Q: have a part with a hole on a slanted surface. In order to show the proper size and location of the…
A: have a part with a hole on a slanted surface. In order to show the proper size and location of the…
Q: 2. Describe what X ray Computed Tomography. What is the minimum feature size that you could image…
A: X ray Computed Tomography: Computed tomography or CT refers to computerized X ray imaging procedure…
Q: HW001 What things we measure with the help of vernier?
A: Given data⇒ Vernier
Q: Plot the graph of the charpy impact test
A: Impact energy: The impact energy of any specimen is a measure of work done to fracture a test…
Q: Continuous level measurement in a tank filled with grain can be done using a _________ sensor.
A:
Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)
A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…
Q: Question 14 The total amount that the feature on the actual part is allowed to vary from the…
A: Allowance: It is the difference between the basic sizes (difference between the hole diameter and…
Q: 6 Which one of the following semi-destructive technique is used for measuring residual stress? a)…
A:
Q: One of the following is false about surface roughness: surface roughness is a measure of the texture…
A: The measurement of small-scale differences in the height of a physical surface is known as…
Q: Slip gauges are standards used along with sine bar for direct angular measurement of workpieces in…
A: Slip gauges are also known as gauge blocks. They are used for the precision measurements. They work…
Q: Draw the iso metric and front view
A: Given : Top and right side view Sketch : front and isometric view
Q: Prompts Submitted Answers Die Choose a match The solid, cylindrical metal stock that is pushed…
A:
Q: Question 2 Select three (3) limitations of Radiography testing. Only internal defects can be…
A: Radiography testing is one of the important and widely used Non-destructive testing methods of…
Q: briefly describe what the impact test practice consists of and what is its purpose? PLEASE I NEED IT…
A: Impact test=The purpose of this test measures the amount of energy absorbed by a material during…
Q: Draw isometric view then complete the top view
A:
Q: List six steps involved in performing a visual inspection.
A: Visual inspection is the method of checking for the defects using naked eye. Visual inspection is…
Q: Spindle is a part of a measuring instrument and it belongs to a. Vernier height gauge b. Micrometer…
A: The Vernier height gauge is a combination of five main components which can be listed as below, 1.…
Q: Read the following statement and choose the most appropriate answers. Statement 1 For a measuring…
A: Accuracy is defined as how close is the measured value to the true value.
Q: installed to enjoy the countryside views and is insisting on it, regardless of the cost. You have a…
A: Disclaimer from Bartleby: Since you have posted a question with multiple sub-parts, we will solve…
Q: 1-What are the most important methods of measuring temperature?
A: We are suppose to solve only one question. Please post other question as a separate question.
Q: Help with dimensioning- It doesn't matter what measurement you will use. I just want to see where…
A: Concept Of Engineering Drawing Is Used
Q: __________ notched specimens are used for Charpy impact test. Select one: V U&V U Key hole
A: The Charpy impact test is used to determine the fracture energy absorbed by the material. In this…
Q: Question 14 The total amount that the feature on the actual part is allowed to vary from the…
A:
Q: Why ceramic block gauges is better than steel slip gauges?
A: Option (b) Due to its resistance to wear is correct option
Q: The following are non-destructive tests which are considered useful for inspecting internal defects…
A: The following are non-destructive tests which are considered useful for inspecting internal defects…
Q: 1MPA = 1N/mm? Select one: True False
A: Given that , 1MPa =1 N/mm
Q: An assembly drawing with numbering of all parts and the dimensions needed only for assembling,…
A: AS per the Question Demand the Drawing of the Power Screw Device. Power Screw Device is the…
Q: (a) Explain TWO reasons why the angle dimensions are necessary in the product design? (b) List THREE…
A:
Q: Please answer it (fill in the blank ) structural analysis ( frame)
A: Given beam as shown below
Q: 8) __________ notched specimens are used for Charpy impact test. Select one: V U & V U Key hole
A: V notched specimens are used for charpy impact test
Q: surface tension analysis of a balloon?
A: Option c) Is correct Answer
Q: I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for…
A: The symbol which is used for surface texture is given below. Readings in the symbol can be given…
Q: How does a strain gauge work?
A: Strain gauge: It is a sensor whose resistance varies with applied force. It then converts force,…
Q: The test conducted by a scan tool can also be tested by some
A: Dear student please rate me positive :) Stay safe stay happy ! Answer- Scan tool : it should be…
Q: Which option is wrong? A bilateral tolerance allows a dimension to vary both above and below…
A: Concept Of Metrology Used
Q: draw top and isometric view
A: According to the details provided in the question, we need to calculate the top view and isometric…
Q: What other geometric tolerance is automatically controlled when parallelism is applied to a surface?…
A: Geometric tolerance is a system that is used for the physical understanding of the design. It…
Q: F1.5 in-| 1.5 in. 1.5 in. 1,5 in. 1.5 in.
A:
Q: Non destructive testing 1. Give your analysis on how NDT can be use in the current industry. 2. Rank…
A: Non destructive testing
Q: In drawing process, compressive forces are used to reduce the cross section of the workpiece.…
A: Drawing is a metal forming process used to reduce cross section and increase length of work piece.…
Q: Draw the isometric view
A:
Q: GIVE FUNCTIONS OF EVERY COMPONENT IN UNIVERSAL TESTING MACHINE (ALL PARTS_
A: A universal testing machine (UTM) is a machine that uses tensile, compressive, or transverse…
Q: 20 In wire drawing process, the cross sectional area of wire is reduced. Select one: True False
A:
Step by step
Solved in 2 steps with 1 images
- the meaning of the graphics belowGiven two views of a multi-view drawing, draw the missing view and then create a 3D isometric sketch of the object.arate port orlov buo ratomotor ar bariupy th copil Design! Q ³x Step by step Proper explanation needed here Importance the eirele in Machine biupts-suprot notes most viss v sol and to A SAMDI Hope to stee tour
- What is the difference between the terms "perspective projection" and "orthographic projection"? "perspective projection" = all the lines from the original point to the projected point intersect at a single point "orthographic projection" = all the lines from the original point to the projected point are parallel "perspective projection" = all the lines from the original point to the projected point are parallel orthographic projection" = all the lines from the original point to the projected point intersect at a single point "perspective projection" = all the lines from the original point to the projected point are parallel "orthographic projection" = all the lines from the original point to the projected point intersect at one of the two focus points of an ellipse "perspective projection" = all the lines from the original point to the projected point intersect at one o the two focus points of an ellipse "orthographic projection" = all the lines from the original point to the…pls help solve question attached imageFind and sketch the FRP view and isometric view.
- EXERCISE 03 DATE: 115 GIVEN THE ORTHOGRAPHIC VIEWWS, CREATE AN ISOMETRIC SKETCH OF THE FOLLOWING OBJECT. VISUALIZATION 6 ENGINEERING DESIGN GRAPHICS WITH AUGMENTED REALITY1. Given the two views of a multiview drawing of an object, sketch the missing top view on paper. Create SolidWorks part models. Compare the top views of the SolidWorks models with your sketch. Each grid is 0.25 inch. (Do not to submit the sketch.) Submit Solidworks part models on Sac CT.3 igen action Senin All Kights Reserved. May sot be scanned, copied or duplicated, or posted to a publicly p 3. paubio Auadoud ajo MADE FRONT 'Z FRONT 3003 For the objects shown in isometric below, sketch the top, front, and right side views in the space provided. Make sure that your views are properly aligned. 1. 2. 78748 4. NO FRONT FRONT.
- orthographic projection : sketch the front, top and right side views of the following two objects using (approximate dimensions. ( draw using appropriate dimensions; use pencil and ruler/scale; make sure you draw and show the projectors) ((Note: including hidden lines) Thank you so much ! 1) 2) In ed the number 2,1 is doneThe distance between a flying drone carrying a laser scanner and a building (Figure 4) is 300m. The distance can be calculated using equation below, where, ris the distance, c is the speed of light and At is the time taken from the laser scanner and the object. r = 1 .c. At 2 Given the building size and shape as in Figure 4. Scanning resolution for this scanner is 4000 points in 1 m?. Consider c = 3.00x10® m/s. Calculate the time taken to scan all possible surfaces of the building. 20 m 40 m 1/8 circle Radius = 25m Width = 40 m 50 m 25 m 10 m 15 m 20 mQuestion 01: a) What do you know about Pro/Engineer software and its applications in the field of Mechanical Engineering? Write down the name of any three CAD softwares? b) Define the following: i. Entity. ii. Parameter. iii. Weak dimensions and weak constraints. iv. Strong dimensions and strong constraints. ICLO-11