119. A 500 mm diameter sewer pipe has been installed with an invert slope of 0.008. Determine the capacity of flow when the sewer pipe is flowing half-full. The number of sewer pipes used is 2, Manning's roughness coefficient is 0.012. Assume that flow in the sewer pipe is uniform.

119. A 500 mm diameter sewer pipe has been installed with an invert slope of 0.008. Determine the capacity of flow when the sewer pipe is flowing half-full. The number of sewer pipes used is 2, Manning's roughness coefficient is 0.012. Assume that flow in the sewer pipe is uniform.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

You are in charge of evaluating a segment of aqueduct pipe (diameter: 30cm). You know that pt. A has a measured pressured of 500 kPa. You must : a) Determine the head-loss between points A and B if they are separated by 100m, that the pipe has a flow of 175 1/s and that the Hazen-Williams coefficient is 100 (see figure 3) b) Calculate the absolute roughness (&). Presume that the water temperature is 15oC. A A Figure 3 Aqueduct pipe c) We wish to limit head-loss to 10 kPa, all the while transporting the same flow between points A and B. To do this, it has been suggested that a second pipe could connect these two points (see figure 4). You must determine this second pipe's diameter knowing that the total length of this secondary pipe is 135m and has the same Manning coefficient as the first pipe. Neglect all local head-loss B Figure 4 Proposed secondary pipe (dotted line) B
Problem #1 (Pipes Iterative Analysis): Water at 70°F flows through 100 feet of pipe 10 inches in diameter with an equivalent roughness e of 0.00085 ft. A head loss of 0.5 feet is measured over this length of pipe, find the flow rate. Use any method, show at least two iterations, neglect minor losses. (v = 1.05 x 10-5ft2/s) (14/100) h = 0.5 ft Total System Head. 8" E=0.00085 ft 100
3.2. A water (Temperature = 20 °C) is flowing in a commercial steel pipe at a flowrate of 5 m³/s. The diameter and length of the pipes are 50 cm and 500 m, respectively. Assume absolute roughness (ɛ) = 0.05 mm. Calculate the head loss by using: (a) Darcy-Weisbach equation (b) Manning's equation (use n = 0.017)
A concrete pipe 750 mm in diameter is laid to a gradient of 1 in 200.The estimated value of Manning’s ?is 0.012m−1/3s.Calculate the discharge when:(a)the pipe is full;(b)the depth is 90% of maximum.Explain why the answer in (b) exceeds th
A 300mm diameter pipe has a flow rate of 200 L/s. Assuming the length of the pipe is 300mm, determine a) friction factor, b) roughness coefficient, and c) Hazen Williams Coefficient (A No answer among the choices in question B (В) с - 93.43 No answer among the choices in question A (D) n = 0.0243 (E) f = 0.0218 (F) c = 87.96 G) c = 107.57 (H) f = 0.0245 ) f= 0.0236 ) f= 0.0257 (K) n = 0.0115 L No answer among the choices in question C (M) n 0.0412 (N) C = 101.09 n = 0.0348
2.32. Water flows at a velocity of 2 m/s in a 300-mm new ductile-iron pipe. Estimate the head loss over 500 m using: (a) the Hazen-Williams formula, (b) the Manning formula, and (c) the Darcy-Weisbach equation. Com- pare your results. Calculate the Hazen-Williams rough- ness coefficient and the Manning coefficient that should be used to obtain the same head loss as the Darcy- Weisbach equation.
3. The 500 mm diameter pipe conveys treated water to supply a municipality with a demand of 40 MLD. Determine the head loss in meter if the length of the pipe is 10 km considering that (a) friction factor f is 0.018, (b) Hazen-William coefficient C is 90, and (c) Mannings coefficient n is 0.015.
Complete solution please. 3DECIMALS thank you Determine the head loss in feet in PIPE 1 Determine the head loss in feet in PIPE 5 Determine the velocity of flow in the lower branch, PIPE 3, in feet per second. Determine the velocity of flow in the upper branch, PIPE 2, in feet per second. Determine the velocity of flow in the lower branch, PIPE 4, in feet per second. Determine the head loss in feet in PIPE 2. Determine the head loss in feet in PIPE 3. Determine the head loss in feet in PIPE 4. Determine the total head loss in feet between the inlet A and the outlet B.
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
Orifice meter with orifis cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauge fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of dischareg using Cd=0.6.
Compute the discharges for the pipes of the network shown below. Use the Hardy Cross method. Only one iteration cycle is required. The Hazen-Williams coefficient is 130 for all pipes. Begin your computation with the assumed discharges given below and verify that they satisfy the continuity requirement. QAB = 2.4 cfs (from A to B) QBD = 1.5 cfs (from B to D) QBC = 0.3 cfs (from B to C) QCD = 0.5 cfs (from C to D) QAC = 1.8 cfs (from A to C)
A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the water is following. The pipe is located at 5 metre above the datum line. The sum of total head and stagnation head is m. (g = 10 m/s?). (assume 1 bar = 105 Pa) %3D