11.24 A swivel C bracket shown in Figure P11-24 is mounted to a ceiling of a building and has a speaker (not shown) of 30 lbf hanging from each mounting hole. The mounting bracket is made of A 36 steel with a modulus of elasticity of 29 x 106 psi, Poisson's ratio of 0.29, and yield strength of 36,000 psi. Determine the maximum von Mises stress and deflection in the bracket. (This problem is by Tyler Austin and Kyle Jones.) V

11.24 A swivel C bracket shown in Figure P11-24 is mounted to a ceiling of a building and has a speaker (not shown) of 30 lbf hanging from each mounting hole. The mounting bracket is made of A 36 steel with a modulus of elasticity of 29 x 106 psi, Poisson's ratio of 0.29, and yield strength of 36,000 psi. Determine the maximum von Mises stress and deflection in the bracket. (This problem is by Tyler Austin and Kyle Jones.) V

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fill in the blanks: Two squared and ground end springs arranged in series. Find the total deflection in mm. The springs have the following specifications. Upper spring: 16 actual coils of 40 mm diameter, Outside diameter of 230 mm. Lower spring: 8 active coils of 30 mm, Outside diameter of 185 mm. The maximum stress in either spring must not exceed 270 MPa. G = 82 GPa
Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside diameter should be limited to 66mm. if the permissible shear stress of the spring material is 325 N/mm? and the Modulus of rigidity is 85kN/mm?. a) Compute the deflection of spring per active turn and the axial load on the spring considering the effect of curvature, take Wahl's factor as Kw= 1.1 b) Calculate the value of axial load neglecting the effect of stress factor. **Note: Please upload your handwritten working/solution to the link provided. The value of Mean diameter of the spring in mm . The Spring Index is. Shear stress factor, neglecting curvature effect . Deflection per active turn in mm Axial Load W in N .. Axial Load W in N. considering effect of curvature .
Ensssprrs wuii. Inside a helical spring of circular cross-section 20 mm in dimater spring is placed having the same cross-section. The mean radius of the outer spring is 80, that of the inner spring is S0 mm. Both the springs are of the same height and have 10 coils With a load being transmitted to both the springs they deflect by 50 mm. In which spring is the maximum shear stress greater, and what are their magnitudes? What is the corresponding load being transmitted? The shear modulus C = 80 GPa for both the spring materials.
4. Find the diameter of steel line shaft to transmit 10 hp at 150 rpm with a torsional deflection not to exceed 0.08 deg foot length.
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14
1. A 0.5-m long solid shaft of a rice thresher is stressed at 100 MPa during operation. If the torsional deflection is 2 degrees, compute the shaft diameter. What power is transmitted by the shaft at 20 Hz? Use G= 83 GPa. %3D
A high alloy spring has an active coil of 16 and modulus ofelasticity in shear of 85 GPa. Compute the Wahl factor. Thespring outside diameter is 9.66 cm and wire diameter is 0.65 cm.
2. Find the size of wire in mm if the maximum design stress is 425 000 KPa. A mass 72.40022026 kg falls from a height of 0.85 m to the center of a horizontal platform mounted on five helical springs. At impact each springs deflects 65 mm. Assume spring index of 8.
Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate of 0.209 kg ∕mm and the other two have equal spring rate of 0.643 kg ∕mm. Find the deflection.
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
A weight of 160 lb falls from a height of 2.5 ft to the center of a horizontal platform mounted on four helical springs. At impact each spring deflects 3 inches. Calculate the wire diameter if the maximum design stress is 60,000 psi and spring index of 5
A helical spring made of oil hardened and tempered steel compression springs, made of circular wire, is subjected to an axial force, which varies from (2.5 KN) to (3.5 KN). Over this range of force, the deflection of the spring should be approximately (5 mm). The spring index can be taken as (5). The spring has square and ground ends. If ultimate tensile strength of (1050 N/mm2) and modulus of rigidity of (81370 N/mm2). The permissible shear stress for the spring wire should be taken as (50 %) of the ultimate tensile strength.Design the spring and calculate the following: 1. Wire diameter; 2. Mean coil diameter; 3. Number of active coils; 4. Total number of coils; 5. Solid length of the spring; 6. Free length of the spring: 7. pitch of coils (p); 8. Required spring rate; 9. Actual spring rate; and 10. Draw a neat sketch .of the spring showing various dimensions