10 100m 54400N Desmos Calculator As seen above a large ocean ship has run aground near the shore. It lies at an angle as illustrated. Salvage crews must apply a torque to rotate the ship in order to float the vessel for transport. A force as seen above is acting at point A and will be appiled straight to the right. What is the torque about the point of contact of the ship with the ground?

10 100m 54400N Desmos Calculator As seen above a large ocean ship has run aground near the shore. It lies at an angle as illustrated. Salvage crews must apply a torque to rotate the ship in order to float the vessel for transport. A force as seen above is acting at point A and will be appiled straight to the right. What is the torque about the point of contact of the ship with the ground?

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 10.6CYU: Check Your Understanding A large ocean-going ship runs aground near the coastline, similar to the...

See similar textbooks

Similar questions

Dima pulls directly backward with a force ?=137 N on the end of a 2.00 m -long oar. The oar pivots about its midpoint. At the instant shown, the oar is completely in the ??- plane and makes a 30.0∘ angle with respect to the water's surface. Derive an expression for the torque vector ?⃗ about the axis through the oar’s pivot. Express the torque using ??? vector notation. ?⃗=???+???+??? I got this as the answer but it is still wrong. Please help me.
A.) what is the torque by the weight of your upper body considering sacrum as the pivot, in lb·m? B.) what is the torque by the weight of the packet considering sacrum as the pivot, in lb·m?
The arm of a crane at a construction site is18.0 m long, and it makes an angle of 15.3with the horizontal. Assume that the maximum load the crane can handle is limited by the amount of torque the load producesaround the base of the arm. What maximum torque can the crane with-stand if the maximum load the crane can handle is 607 N?
10kg rigid beam that is 3mlong is supported at each end. An8kg block is placed 2m fromsupport 1. How much upward forcedoes each support provide to ensurezero acceleration and zero torque?Note, if an object is not rotating, itis not rotating about every axis.
A person exerts a horizontal force of 46N on the end of a door 97cm wide. What is the magnitude of the torque if the force is exerted a) perpendicular to the door? b) at a 60o angle angle to the face of the door?
Find the amount of torque needed to push open a door in each of the given scenarios:A. You push with 10 N at the edge of the door (0.8 m from the hinge), perpendicular to the doorB. You push with 10 N at the center of the door, perpendicular to the doorC. You push with 10 N at the edge of the door, but at an angle of 30 degrees between your push and the doorWhich push is most effective?
The 25 N force F is applied to a corner of the rectangular plate of sides a = 0.50 m, b = 0.70 m. The angle θ is 37deg. a) Find the torque on the plate about i) the corner A, ii) the corner B, and iii) the corner C. Give both the magnitude and direction (clockwise or counterclockwise) in each case.
The (Figure 1) shows two thin beams joined at right angles. The vertical beam is 12.0 kg and 1.00 m long and the horizontal beam is 21.0 kg and 2.00 m long. Neglect the lateral dimensions of the beams.Calculate the gravitational torque on the joined beams about an axis through the corner.
Two blocks, each of mass 2 kg are suspendedfrom the ends of a rigid massless rod of lengthL. The rod is held horizontally on the fulcrumand then released. The length L1 is 15 cm andthe length L2 is 85 cm. Draw the force diagram for the rod. Clearly label all forces. Write Newton’s 2nd Law equation: (for F of y) Write Newton’s 2nd Law equation: (for net torque) What is the magnitude of the linear acceleration of the block closest to the fulcrum? What is the magnitude of the linear acceleration of the block furthest from the fulcrum?
Dima pulls directly backward with a force F=137 N on the end of a 2.00 m-long oar. The oar pivots about its midpoint. At the instant shown, the oar is completely in the ??-yz-plane and makes a 30.0∘ angle with respect to the water's surface. Derive an expression for the torque vector ?⃗ τ→ about the axis through the oar’s pivot. Express the torque using ???ijk vector notation. ?⃗ =???+???+??? ?⃗ =?N*m
PLEASE HELP ME IN MY SUBJECT PHYSICS (CENTER OF GRAVITY) THANKYOU SO MUCH IN ADVANCE TUTOR! Two boys and a Man decided to play in a seesaw 6 m long. The two boys seated on the left sideof the fulcrum while the Man seat on the right side. The boys seat 0.5 m apart., the boy onbehind seats 0.5 m from the left edge. Boy 1 exerts 80 N while Boy 2 exerts 70 N. The manexerts 200N . Where should the man seat from the fulcrum in order to balance the seesaw?Find also the reaction force exerted by the fulcrum. Make the fulcrum as the point of referencefor moment. Draw the FBD
The bear of weight 700 N walking on the horizontal beam pivoted at point A and supported by a rope at an angle 60∘ on point B. The bear wants to reach a basket full of honey. The basket weighs 80 N. The honey basket weighs 200 N, and the beam length 6 m. When the bear in at ? = 1 m, a. Find the tension of the rope supporting the beam. b. What is the component of the forces exerted on the wall (point A)?