LABORATORY ACTIVITYAPPLICATION OF BERNOULLI'S THEOREMQUESTIONS:1. As the fluid flows through the section, describe how the velocity, pressure, andelevation heads change. Determine the location of the section's maximumvelocity and pressure.2. What method does the apparatus use to capture energy loss? You could usemathematical equations to explain your point.3. What will happen to the corresponding kinetic and potential heads if theflowrate passing through the apparatus is increased?

Step: 1 “Since you have asked multiple questions, we will solve the first question for you. If you…

Answered: 1. As the fluid flows through the…

1. As the fluid flows through the section, describe how the velocity, pressure, and elevation heads change. Determine the location of the section's maximum velocity and pressure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the velocity is not uniform in the plastic tube, what is the effect of this on the Bernoull equation?
Fluid Mechanics. Reg.no : 5393 Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and that the water jet has a velocity of (Reg.No/100) m/s and a diameter of 60 mm. Find (a) the component of the force acting on the blade in the direction of the jet; (b) the force component normal to the jet; and (c) the magnitude and direction of the resultant force exerted on the blade. Note: Assume reasonable values for any missing data. Symbols have usual meaning unless otherwise stated.
(b) An incompressible viscous liquid flows down a plate inclined at angle 8 as shown in Figure 4. The flow is assumed to be steady and the film thickness is constant. The density of the liquid is p, its dynamic viscosity is μ and the film thickness is h. Y₁ 0 0 8 ↓ 11 Figure 4 (i) Show that the governing equation for the velocity u(y) can be written as: ² pgsine = Əy² fl (ii) What are the boundary conditions at y = 0 and at y = h ? (iii) The velocity u(y) can be written as expression for C. (iv) What is the average velocity of the liquid film for unit depth (into paper)? u(y) = Cy(2h - y). Determine the
In the Figure Q2(b), show the condition of stability of floating object in a fluid. Describe the method of determining Stability of Floating Bodies. Then, with the aid of diagram, illustrate the condition of unstable floating bodies. GB CB • he hal
2. 0.1 m at a constant temperature and pressure seen in the figuren water flowing through a diameter pipe with a mass flux of 6000 kg/m's, then a 0.3 m diameterpipe with orifice attached to it it is transitioning to the line. The orifice-bound and manometer sIVisi ilcm between arms in the manometer containing mercury the difference has been observed to be. As a result of the measurements made the origins of permanent pressure loss, pressure loss It was found to be up to 81%. Accordingly; a) permanent pressure in the pipe due to orifice calculate the loss in terms of pascals (APK receiver). B) calculate the linear velocity value in the orifice (V)). orifis Drection of fow D, = 0.1 m D, = 0.3 m G. = 6000 kg / m2s h=1 cm Data: • Pau = 1000 kg / m2, = 13600 kg / m3 %3D
kerosene is placed inside a glass capillary tube having a radius of 0.5mm. the kerosene inside the tube is measured to have a standing height of 59mm. determine the true static height of the kerosene using the surface tension value if 0.035N/m and Sg=0.8 Final answer in mm.
10. What is the maximum elongation of a helical spring which is made of phosphor bronze composed of 20 turns of 20 mm diameter wire with a mean radius of 80 mm when the spring is stressed to 140 MPa, for which G = 42 GPa? a. 226 mm b. 242 mm c. 235 mm d. 250 mm
Derive an expression for the capillary rise between two vertical parallel plates of width b partially immersed in a liquid of specific gravity S in terms of the distance t between the plates, surface tension o and the contact angle 0 between the liquid and the plates.
please i dont have much time solve fast as you can When the angle θ = 90 °, the BE hydraulic cylinder applies a vertical force (F = 3330 N) Newtons to the platform. The mass of the crate is 200 kg and the angular velocity (ω) of AB is 7 (rad / s). First, treat the box and platform as a single body to find the following: The amount of reaction forces at points B and D. Acceleration of the center of the box aG in the x and y direction. Second, after finding the previous requirements, find the following for the platform only: The force of reaction from the box to the platform (Normal force). Minimum static friction coefficient (μs) to ensure the box does not slip. Note: Neglect the weight of the platform and objects AB and CD.
se that 1 of 1 Consider the frame shown in (Figure 1). Suppose that F₁ = 850 N Figure 200 N/m Y Part C FA= Y Part B Submit 60° Determine the magnitude of the reaction at pin A Express your answer to three significant figures and include the appropriate units. Submit PA Value Request Answer A μÁ FB = Value Request Answer Fo= Value Determine the magnitude of the reaction at pin B. Express your answer to three significant figures and include the appropriate units. 2m Units Submit Request Answer Units - 0 < 1 of 1 Determine the magnitude of the reaction at pin C on CB Express your answer to three significant figures and include the appropriate units. Units ? ? 2m ?
3.5. Consider a Pitot static tube mounted on the nose of an experimental airplane Pitot tube measures the total pressure at the tip of the probe (hence sometimes called the Pitot pressure), and a Pitot static tube combines this with a simultaneous measurement of the free-stream static pressure The Pitot and free-stream static measurements are given below for three different flight conditions Calculate the free-stream Mach number at which the airplane is flying for each of the three different conditions 1 01 x 10$ N/m? (a) Pitot pressure (b) Pitot pressure (c) Pitot pressure = 1 22 x 10' N/m², static 7222 lb/ft?, static pressure 13107 Ib/ft?, static pressure pressure 2116 lb/ft? 1020 lb/ft?
Water flows steadily from a nozzle into a large tank as shown below. The water then flows from the tank as a jet of diameter d. (a) Using the piezometer tube shown, determine the flow rate through the nozzle. (b) Using the flow rate determine the value d if the water in the tank remains constant. Viscous effects are negligible.