4. A 9-tooth sprocket operating at 200rev/min drives a 23-tooth sprocket. Thepitch of this chain is 41.4 mm and the ultimate strength is 9.34 kN. Calculatethe average linear speed, recommended maximum power and averagetorque applied to the drive shaft at recommended power.

Answered: Image /qna-images/answer/4d8bdab8-9504-4515-aba4-f9800b99622d.jpg

1. A 9-tooth sprocket operating at 200rev/min drives a 23-tooth sprocket. The itch of this chain is 41.4 mm and the ultimate strength is 9.34 kN. Calculate he average linear speed, recommended maximum power and average orque applied to the drive shaft at recommended power.

1. A 9-tooth sprocket operating at 200rev/min drives a 23-tooth sprocket. The itch of this chain is 41.4 mm and the ultimate strength is 9.34 kN. Calculate he average linear speed, recommended maximum power and average orque applied to the drive shaft at recommended power.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: (4) A single square-thread power screw has an input power of 3.0kW at a speed of 1 rev/s. The screw…

Q: A single square-thread power screw has an input power of 3 kW at a speed of 1 rev/s. The screw has a…

A: Given: Input power , P=3 kWspeed , N=1 rev/sdiameter of screw,ds=40 mmpitch of the screw, p=8…

Q: keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578…

A: Given:Torque delivered by keyed sprocket, T=778.8 N-mouter diameter of shaft, d=54 mm or 0.054 mkey…

Q: 3. A flat annular steel flywheel of outer radius 0.5 m and inner radius 0.125 m with p = 7800…

Q: 2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is…

A: Find the maximum torque .

Q: A 90 cm pulley transmits 75 kW at 750 rpm. The arc of contact between the belt and pulley is 135…

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

Q: Q. A steel wire 2 mm diameter is held between chucks 1 m apart. The wire weighs 0.24 N/m. The…

Q: 1. A single-threaded 25-mm power screw is 25-mm in diameter with a pitch of 5mm. A vertical load on…

Q: Calculate the pressure between a shaft with an outer diameter of 0.034 m and an inner diameter of…

Q: A 915 mm diameter driving pulley is used to drive 1,220 mm pulley. The center to center distance…

Q: A keyed sprocket delivers a torque of 778.8 N - m thru the shaft of 54 mm OD. The key thickness is…

Q: The rotation in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 10 mm in radius and…

A: Given: The shaft length, L = 800 mm = 0.8 m The torque applied, T = 80 N.m The radius of shaft, r =…

Q: Design a cast iron driven pulley to transmit 20 kW at 300 r.p.m. The diameter of the pulley is 500…

A: Given data as per question Power transmitted =20 kw speed =300 rpm Diameter of pulley =500 mm Radius…

Q: Design and draw a cast iron flange coupling for a mild steel shaft transmitting 80 kW at rpm with…

A: solution CAST IRON FLANGE COUPLING Power transmitted P=80kN speed N=220rpmallowable shear stress in…

Q: A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of…

A: Answer: (a) The efficiency of the jack for raising the load: 8.9206 % (b) The power required to…

Q: The inner and outer radii of a hollow steel shaft are 50 mm and 100 mm, respectively. The hub of a…

A: Given Inner radii of hollow shaft ri=50 mm Outer radii of hollow shaft ro=100 mm Maximum allowable…

Q: The shaft whose torque varies from 3000 to 8000 in-lb has 2 inches in diameter and 60 000 psi yield…

Q: 5. Compute the force necessary to move a 6000 lbs supported on four wheels of 2.5 ft diameter,…

A: In Question 4 some data is missing (length or Diameter) so I am attempting the Question 5 Given…

Q: Find the power lost in friction assuming i)uniform pressure and ii)uniform wear,

A: The diameter of the vertical shaft is, D=100 mm The rotational speed of the shaft is, N=150 rpm The…

Q: A motor is driving a solid circular steel shaft transmits 40kW of power at 500 rpm. If the diameter…

Q: Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being…

Q: A power screw (square) thread of dm= 40 mm, u=0.4 . Find the maximum value for the thread pitch (L)…

A: dm=40mm μ=0.4p=mg=3×1000×9.81N=29430Np=29430N

Q: A cast-iron pulley transmits 49 kW at 1,750 rpm. The shaft to which it is to be keyed is 44.4 mm in…

Q: pulleys at -ach 400 mm ring and are own below. e shear stress of Pa, calculate the d for this raw…

Q: The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in…

Q: W at a speed of 1 rev/s. The screw has a major diameter of 36mm and a pitch of 6mm. The frictional…

A: Given as, Power=3KN =3000W N=1rev/s d=36mm p=6mm u=0.14 for…

Q: A flange coupling is to connect two 57mm shafts. The hubs of the coupling are each 111m in diameter…

Q: Design of a Shaft subjected to Alternating Loads 1. [Proof of Concept] Considéra machined steel…

A: Consider Tmax as the maximum torque, Tmin as the minimum torque, Mmax be the maximum bending moment,…

Q: The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum…

Q: A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter…

A: GIVEN DATA- m=585kg dm=20mm p=5mm Coefficient of friction =0.1 We have to find torque required to…

Q: A 1.5 in diameter 10-spline shaft and permanent fit has a compressive force of 2000 lbs. Find the…

A: Write the formula for internal diameter of the 10-spline shaft. d=0.91D Here, D is the outer…

Q: A 2. The lift cage in Figue N2 is boisted by 6 Drum means of a rope wound round a 0344 (m] diameter…

A: Given: The diameter of the drum, d = 0.344 m The number of tooth on gear 1, Z1 = 80 The number of…

Q: A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm.…

Q: A load of 20 kN is supported by a conical pivot. The angle of cone is 120° and intensity of pressure…

A: The outer and inner radii of conical pivot bearing is required to be calculated alongwith power…

Q: A 3/8 inch flat leather belt is 12 inch wide and is used on a 24 inch diameter pulley rotating at…

Q: 2. A flat belt runs over two pulleys of diameter 800 mm and 1,400 mm with center distance 24 m. A…

A: given small pulley diameter d1 = .8 m large pulley diameter d2 = 1.4 m Power 90kWslip =…

Q: Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm…

Q: QI: A double-threaded 30-mm power screw is 30 mm in diameter with a pitch of 6 mm. The coefficients…

A: The power screws (also known as translation screws) transform rotational motion to translatory…

Q: B) Estimate the minimum shaft diameter according to the maximum shear stress theory for a shaft…

Q: mm diameter and a drive pulley of 200 mm diameter, whose centres are 1000 mm apart. The driving…

Q: (6) A double square-threaded power screw transmits 1,800in-lb of torque and raises a machine head;…

Q: Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The…

A: Given DataP=15kWN=1000 rpmTs=60MPaTbolt=25 MPa

Q: Two 400 mm diameter pulleys are keyed to a simply supported shaft 500 mm apart. Each pulley is 100…

Q: friction are 0.06 for th

Q: A 600 mm steel pulley transmits 50 kW at 900 rpm. The arc of contact between the belt and pulley is…

Q: A pullev 615 mm in diameter transmits 40 kW at 630 rpm The arc of contact between the belt and the…

Q: A leather belt which is 125 mm wide and 6 mm thick, is used for transmitting power from a pulley.…

A: Given l= 125 mm w = 6mm d = 750 mm n = 500rpm Theta = 150o Mass ratio with volume = 1 m3 for 1 kg…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

4. A 9-tooth sprocket operating at 200rev/min drives a 23-tooth sprocket. The
pitch of this chain is 41.4 mm and the ultimate strength is 9.34 kN. Calculate
the average linear speed, recommended maximum power and average
torque applied to the drive shaft at recommended power.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
Machine design A 60-hp four-cylinder internal combustion engine is used to drive a medium-shock brickmaking machine under a schedule of two shifts per day. The drive consists of two 26-in sheaves spaced about 12 ft apart, with a sheave speed of 400 rev/min. Select a Gates Rubber V-belt arrangement. Find the factor of safety, and estimate the life in passes and hours?
A keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. (Ans: 4.33 cm)
Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angleare in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh.The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at eachpair assuming equal direction of load between the pairs. Neglect friction.
6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
To transmit 20 kW at 1000 rpm with a service factor of 3, a rigid flange coupling should be designed. Find the size of the shaft, the key and the flange if the shaft and the key are made of steel with allowable shear stress of 100 MPa and allowable crushing stress of 220 MPa and the flange is made of cast iron with allowable shear stress of 12 MPa.
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
Q1/ A 6-in-wide polyamide F-1 flat belt is used to connect a 2-in-diameter pulley to drive a larger pulley with an angular velocity ratio of 0.5. The center-to-center distance is 9 ft. The angular speed of the small pulley is 1750 rev/min as it delivers 2 hp. The service is such that a service factor Ks of 1.25 is appropriate. (a) Find Fc, Fi, Fla, and F2. (b) Find Ha, nfs, and belt length. (c) Find the dip.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution