1. A 2F capacitor is connected in series with a diode and a 60 resistor. The voltage of the battery is 9V. The forward voltage drop of the diode is 0.7V. Flip to close the switch at t=0. Determine the voltage and current of the capacitor at t=0, t=12s, t=24s, and t=36s. (The following table may help you with this question. Feel free to use this table (or not).) Vc VR I R1 60 H Time=0 Time=12s Time=24s Time=36s

1. A 2F capacitor is connected in series with a diode and a 60 resistor. The voltage of the battery is 9V. The forward voltage drop of the diode is 0.7V. Flip to close the switch at t=0. Determine the voltage and current of the capacitor at t=0, t=12s, t=24s, and t=36s. (The following table may help you with this question. Feel free to use this table (or not).) Vc VR I R1 60 H Time=0 Time=12s Time=24s Time=36s

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
PROBLEM: The diode (blue line) should be at -10V not -8V SOFTWARE USED: LTspice XVII---Figure 1 is my work, and figure 2 is the correct sample. Please tell me what I did wrong. Thank you :))---Below is the .asc filehttps://www.mediafire.com/file/zxauoh86zi79nfu/EXPERIMENT_01.asc/file
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
6. A varactor diode exhibits (a) a variable capacitance that depends on reverse voltage (b) a variable resistance that depends on reverse voltage (c) a variable capacitance that depends on forward current (d) a constant capacitance over a range of reverse voltages
The thickness of the PN depletion region increases when diode is Your answer The function of zener diode is to provide a constant output voltage to a load. this process is called Your answer One types of diodes are typically used for power supply applications which always called Your answer
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
What is the drop across the diode when it is connected in series to a resistor of 1.8 k2 and a supply voltage of 50 V. The supply voltage causes the diode to be reverse-biased. * O A. 50 V O B. 0.7 V O c. 0.3 V O can not be solve, lack of data
In the circuit shown in the figure, the switch is operated at a duty cycle of 0.5. A large capacitor is connected across the load. The inductor current is assumed to be continuous. The average voltage across the load and the average current through the diode will respectively be =4A L L=t A 20 V'
The voltage signal coming out of the capacitor is with small ripples compare to the voltage signal out of the diode. True False