Answered: 1-In series R-L circuit transients, the…

1-In series R-L circuit transients, the momentary current imm is directly proportional to the RMS voltage. Select one: True False

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.2MCQ: Even though the fault current is not symmetrical and not strictly periodic, the rms asymmetrical...

See similar textbooks

Related questions

Q: Three-bus system network consists of TWO generators located at buses 1 and 2 and TWO loads located…

A: The Given is V1=j0.5∠0° and V2=1.03, PG2=2pu SD2=0.5+j0.2 and SD3=0.6-j0.25 The Given Matrix is…

Q: 1. Given the network as shown below, determine the three phase, single line to ground and line to…

A: In this question we need to find a three phase, SLG and LL fault at fault location shown in the…

Q: The sample power system subjected to three phase fault at bus 4. The system values are given below…

A: Find explanation below

Q: Consider the one-line diagram of power system shown below; a) Develop equivalent circuit expressing…

Q: For the power system shown at right the impedance matrix (2 is j0.4 3 j0.5 j0.2 0.164 0.101 0.0692…

Q: For the four bus system as shown in Fig. Determine the fault current when the fault takes place at…

A: In this question , we will find fault impedance and current...

Q: .A 33 KV line has a resistance of 4 ohm and reactance of 16 ohm respectively. The line is connected…

A: Given R=4 ohm X=16 ohm Let 10000 KVA be the base KVA Reactance of generator 1 Xg1=10 %…

Q: (Q.1) The admittance matrix (Ybus) of a three-bus power system is given by: Y1--j12, Y12-Y21 =j5,…

A: There will be three sequence networks in the given power system- Positive-sequence network…

Q: For the four bus system as shown in Fig. Determine the fault current when the fault takes place at…

A: In this question , we will find fault impedance, fault current and current from generator 1..

Q: please write introduction about Analysis of 3 Phase star connected circuit Note:please write details…

Q: Problem-4: Solve at Home Problem-4, Cont... The one-line diagram of a simple three-bus power system…

Q: For the four bus system as shown in Fig. Determine the fault current when the fault takes place at…

A: In this question we need to find a Thevenin impedance , fault current and fault current from…

Q: A 3-phase transmission line operating at 33 kV and having a resistance of 5 2 and reactance of 20…

A: Given data, Sbase=15,000 kVASbase=15 MVA Single line diagram of the system,

Q: For the network shown in the figure below, all reactances are in p.u. to a base of 100MVA and 13.8…

A: The power system is a network consist of power generation, transmission, and distribution. Power…

Q: The value of symmetrical short circuit current is ___________________ at time t=0. Zero Minimum…

A: In this answer let us discuss the concept of short circuit current and try to find its value at t=0.

Q: Figure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault…

A: Note: Here line impedance as well as Z bus matrix impedance are given We are going to solve the…

Q: Hourly variation factor need to consider while dealing with the non-coincidence demand of different…

A: A power station is to provide electricity to a huge number of people. Different customers' power…

Q: Problem 2.. Determine the 3×3 bus admittance matrix Yous for the 3-bus circuit in the figure below.…

A: Given circuit diagram, YBUS =?

Q: The total instantaneous power absorbed by a three-phase motor (under balanced steady-state…

A: Consider the instantaneous voltage across phase a and the neutral terminal is given by:

Q: Problem2 A generator having H = 6.0 MJ /MVA is delivering power of 1 per unit to an infinite bus…

Q: For the four bus system as shown in Fig. Determine the fault current when the fault takes place at…

A: In the power system circuit Fault at the bus3 Find the equivalent Reactance across the fualt. Total…

Q: A generating plant containing three identical 40 MW generating units is connected to a constant 82…

A: SI No Unit Failure rate Repair time Frequency Duration Failure probability 1 40 MW 3…

Q: A 30-MVA alternator with 15% reactance is connected to a bus bar. A second alternator rated 25-MVA…

A: The solution is given below

Q: A generator-transformer unit is connected to a line through a circuit breaker. The unit ratings are:…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: 2. A 3-phase, 75 MVA, 11-8 kV star-connected alternator with a solidly earthed neutral point has th…

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again.

Q: In a short circuit test on 132 kV, 3-phase system, the breaker gives the following results: Power…

Q: 2) For a given short-circuit calculation utilizing the per unit method, a base voltage of 480 V and…

A: Given, Base voltage, Vb=480 V Base power, Sb=2500 kVA

Q: The base current and base voltage of a 345 kV system are chosen to be 3000A and 300kV respectively.…

A: The solution is given below

Q: -The voltage magnitude and phase angle are the quantities to be determined after load flow analysis…

A: The voltage magnitude and phase angle are the quantities to be determined after load flow analysis…

Q: A private developer proposes to install a synchronous type generating plant connected to the local…

A: Answer(1) According to the given data The generator produces 14 MW at 11 kV So, during the peak…

Q: For the four bus system as shown in Fig. Determine the fault current when the fault takes place at…

A: In this question , we have to find out fault current through fault point when fault occur at bus…

Q: A three-phase fault with a fault impedance Zf = jo.16 per unit occurs at bus 3 in the Figure beside,…

A: The solution is given below

Q: For the four bus system as shown in Fig. Determine the fault current when the fault takes place at…

A: In this question , we will find thevenin impedance across fault point and fault current in pu..

Q: In a short circuit test on a 130 kV, 3 phase system, the breaker gave the following results: p.f. of…

Q: Q3: Derive the relationship between positive and negative sequence components when single phasing…

A: Single phasing Three phase supply is fed to a load e.g. induction motor When one of the phase is get…

Q: From the system as shown below with base of 100 MVA by neglecting all parallel admittance. (a)…

A: Since there is two bus in the system, so Size of Ybus matrix will be 2×2.…

Q: The bus impedance matrix for a three-bus power system has per-unit elements as: Z11 = 0.5 Z12 = 0.4…

A: In this question we need to find a subtransient fault current when a 3 phase fault occur at bus 3.

Q: For the power system shown at right the impedance matrix 2 is j0.5 j0.2 3 j0.4 0.145 0.120 0.0692…

A: New voltage at a bus = old bus voltage + change in voltage

Q: The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: If the source impedance at a 13.2 kV distribution substation bus is (0:5 + 1:5) Q per phase, compute…

A: Given, The line voltage,VL-L=13.2kVThe impedance is,Z=(0.5+j1.5)ΩZ=(0.5)2+(1.5)2=1.58ΩThe…

Q: A surge of 100 kV travels along an overhead line towards its junction with a cable. The surge…

A: we need to determine magnitude of surge transmitted through cable.

Q: Choose the right answer. 1. The symmetrical component method is …………. 2. Conditions for succesful…

A: 1) Symmetrical component method:- This method is used to solve the set of coupled equations. In this…

Q: For the four bus system as shown in Fig. Determine the fault current when the fault takes place at…

A: When there is a three phase fault i.e LLL or LLLG fault will occur in the network, the current of…

Q: Most buses in a typical power-flow program are a.voltage controlled bus b.PQ bus c.PV bus…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: In the shown below power system, both generators G1 and G2 emf's are equal. All the system data are…

Q: In a short circuit test on a 120 kV, 3 phase system, the breaker gave the following results: p.f. of…

A: We have an breaker with the following data, KV = 120 KV Power factor of fault = 0.6 Natural…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

1-In series R-L circuit transients, the momentary current i_mmis directly proportional to the RMS voltage.

Select one:

True

False

2-Symmetrical components method are used to solve the symmetrical faults.

Select one:

True

False

3-If the circuit has leading power factor, then it is called as _______________ circuit.

Inductive

Capacitive

Resistive

Resistive and Inductive

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What are the hazards of phase failure and phase reversal?
estion 9 The fault current level of a circuit breaker used in a transmission line with phase voltage 2.2 kV and breaking capacity 50 MVA is yet ......kA. vered -ked out of Flag question estion 10 The voltage between lines in a transmission line is the maximum value of the sine waveform. yet vered Select one: -ked out of O True Flag question O False
Circuit breaker usually operate under A) after D. C. component has ceased B) transient state of short-circuit current C) sub-transient state of short-circuit current D) steady state of short-circuit current
"As per the standards used in power system, even harmonics are limited to 25 percent of the odd harmonic limits" True False
Describe the concept of power system harmonics and their impact on the quality of electrical supply.
Which of the following statements is/are true? A In purely resistive circuit, the current lags voltage. (B In purely capacitive circuit, the voltage lags current. In purely resistive circuit, the current is in phase with voltage. D In purely inductive circuit, the current leads voltage.
10) In carrier current protection the purpose of the wave trap is for trapping power frequency waves trapping high frequency waves entering into generators/ transformer unit both (a) and (b) none of the above
Discuss the concept of fault analysis in power systems. What are the types of faults and their effects?
Voltage sags due to short circuit and earth faults are the cause for the vast majority of equipment problems. Electronics equipment become more susceptible to voltage sag, hence the companies experience production stoppages. Voltage sag analysis is very complex issue. Based on voltage sag randon factors describe on it.
Describe the effects of harmonics on power distribution system.
Even though the fault current is not symmetrical and not strictly periodic, the rms asymmetrical fault current is computed as the rms ac fault current times an asymmetry factor, which is a function of _______.
Equal area criteria is a method used to calculate: Select one: O a. None of the answers b. Critical clearing angle and time for transient faults O c. Critical clearing voltage angle for transient faults d. Transient stability current limit O e. Steady state stability power limits