1) In an ideal regenerative Rankine cycle, vapor enters the turbine at 7MPa and 550°C. Steam first expands to 0.8MPa where some of the steam is extracted and transferred to an open feedwater heater (FWH) operating at 0.8MPa. The remaining steam expands through the second-stage turbine to the condenser pressure of 10kPa. Saturated liquid exits the open FWH at 0.8MPa and water enters pump I as a saturated liquid. Determine a) the power output of the cycle in kJ/kg b) the thermal efficiency of the cycle c) the heat transfer from the condenser to the environment, in kJ/kg. Boiler Pump II Open FWH Pump I Turbine Condenser

1) In an ideal regenerative Rankine cycle, vapor enters the turbine at 7MPa and 550°C. Steam first expands to 0.8MPa where some of the steam is extracted and transferred to an open feedwater heater (FWH) operating at 0.8MPa. The remaining steam expands through the second-stage turbine to the condenser pressure of 10kPa. Saturated liquid exits the open FWH at 0.8MPa and water enters pump I as a saturated liquid. Determine a) the power output of the cycle in kJ/kg b) the thermal efficiency of the cycle c) the heat transfer from the condenser to the environment, in kJ/kg. Boiler Pump II Open FWH Pump I Turbine Condenser

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An ideal RANKINE cycle delivers 210 MW of power. Steam enters the turbine at 10 MPa and500C and is cooled in a condenser at 10 kPaa. Determine the thermal efficiency of this cycleb. Mass flow of waterc. Heat rejected in the condenserd. Work inputted to the pump (remember the volume is constant)
4) In a reheat Rankine cycle, water vapor enters the high-pressure turbine at 9MPa and 450°C. It is expanded to an intermediate pressure of 0.8MPa and enters the low-pressure turbine with a temperature of 400°C. Condenser pressure is 7.5kPa and water enters the pump as a saturated liquid. There is no pressure loss in the piping that connects the cycle components. Water mass flow rate is 60 kg/s and both turbines have an isentropic efficiency of 90%. Calculate mankan kunne tħe b) net power output, in MW
4) In a reheat Rankine cycle, water vapor enters the high-pressure turbine at 9MPa and 450°C. It is expanded to an intermediate pressure of 0.8MPa and enters the low-pressure turbine with a temperature of 400°C. Condenser pressure is 7.5kPa and water enters the pump as a saturated liquid. There is no pressure loss in the piping that connects the cycle components. Water mass flow rate is 60 kg/s and both turbines have an isentropic efficiency of 90%. Calculate a) heat transfer from the condenser, in MW
4) In a reheat Rankine cycle, water vapor enters the high-pressure turbine at 9MPa and 450°C. It is expanded to an intermediate pressure of 0.8MPa and enters the low-pressure turbine with a temperature of 400°C. Condenser pressure is 7.5kPa and water enters the pump as a saturated liquid. There is no pressure loss in the piping that connects the cycle components. Water mass flow rate is 60 kg/s and both turbines have an isentropic efficiency of 90%. Calculate c) thermal efficiency of the cycle. (
a. Calculate the thermal efficiency and turbine-exit quality for an Ideal Rankine Cycle where the steam exits boiler at 5MPa, 450C and the condenser pressure is 15 kPa. Draw the systems and the Ts diagram for the process. b. Calculate also the thermal efficiency and turbine-exit quality if the system is modified to an Ideal Reheat Rankine Cycle where the reheat takes place at 1 MPa and the steam leaves the reheater at 500C. Draw the systems and the Ts diagram for the process and discuss your findings of these two systems.
1. In an ideal reheat-regenerative cycle, steam enters the turbine at 6 MPaa and 400°C. After expansion to 1.4 MPaa steam is withdrawn and reheated to 300°C. Extractions for regenerative heating occur at 0.15 MPaa and 1.4 MPaa and the condenser pressure is 0.01MPaa. Use mass flowrate of 1 kg/s. a. Sketch the schametic diagram showing the correct state points and its components b. Sketch the T-s diagram showing the states
A Rankine cycle using superheat and reheat applications. Steam enters the stage 1 turbine at 8 MPa and a temperature of 480°C and expands at a pressure of 0.7 MPa. The steam is then reheated to a temperature of 440°C before entering the stage 2 turbine, where the steam expands in the condenser at a pressure of 0.008 MPa. The net power generated is 100 MW. Calculate : A) the thermal efficiency of the cycle, B) the mass flow rate of the steam, C) the rate of heat transferred from the condenser to the surroundings (Qout)
Calculate the work done in the low-pressure turbine (LPT) of a Rankine cycle with reheat. The steam enters the LPT at 425°C & 60 MPa and leaves LPT as superheated steam at 375°C & 50MPA. Suggest what would be the dryness fraction of the working fluid entering the condenser.
3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kg 20.01%, 2667.841715.52955.97 k, 3.74, 952.32,35.69%, 3.78 kg kWh Specific Volume Internal Energy Temp Enthalpy Prom MP Entropy Sal Sat, Sat. Liquid Sat. Sat. Liquid Evap. Vapor Liquid Uy Evap. Sat. Vapor t Р 10% Evap. Vapor Up u, hr Liquid S, h h₂ 8% 8₂ 006113 .01 1.0002 206 136 .0007 1.89 1.0001 181 255 3.77 1.0001 159 675 1.0001 142 789 0005 ,00 2375.3 2375.3 7.90 2370.0 2377.9 15.81 2364.7 2380.6 22.88 2360.0 2382.9 01 2501.3 2501.4 7.91 2496.9…
3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa where some steam is extracted for feedwater heating while the rest is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kJ kj kJ kJ kJ kg 1715.88- 20.01%, 2667.84- 955.97 3.74 951.96 35.68%, 3.78. " J kg kg kg kg kWh kg "
In a reheat cycle steam at 8.5 MPa and 490 o C enters the turbine and expands to 1.5 MPa. At thispoint, the steam is withdrawn and passed through a reheater. It re-enters the turbine at 1.3MPA and 720 o C. Expansion now occurs to the condenser pressure of 0.006 MPa. For the cycledetermine. (a) Qa (b) Went and (c) cycle thermal efficiency. For the engine, determine theengine thermal efficiency and the steam flow rate for an engine output of 40 MW. Also draw the T-S diagram.
1. Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of45 MW. Steam enters the turbine at 7 MPa and 500°C and iscooled in the condenser at a pressure of 10 kPa by runningcooling water from a lake through the tubes of the condenserat a rate of 2000 kg/s. Show the cycle on a T-s diagram withrespect to saturation lines, and determine (a) the thermal efficiency of the cycle, (b) the mass flow rate of the steam, and(c) the temperature rise of the cooling water. Answers:(a) 38.9 percent, (b) 36 kg/s, (c) 8.4°C 2. Consider a 210-MW steam power plant that operateson a simple ideal Rankine cycle. Steam enters the turbine at10 MPa and 500°C and is cooled in the condenser at a pressure of 10 kPa. Show the cycle on a T-s diagram with respectto saturation lines, and determine (a) the quality of the steamat the turbine exit, (b) the thermal efficiency of the cycle,and (c) the mass flow rate of the steam. Answers: (a) 0.793,(b) 40.2 percent, (c) 165…