... P1 = 50 KPa %3D P2 = 10 KPa 4m OIL 1.6m OIL In the figure, an orifice is locates in the partition wall so that it discharges oil (SG = 0.8) from left to right side of the room. The orifi has a diameter of 100mm and is under the surface of oil, 4m from the surface on the left and 1.6m from the surface on the right. The surface at the left is under 50KPA of pressure and the surface at the right side is under 10KPA of pressure. Determine the actu discharge in the orifice if C = 0.92

... P1 = 50 KPa %3D P2 = 10 KPa 4m OIL 1.6m OIL In the figure, an orifice is locates in the partition wall so that it discharges oil (SG = 0.8) from left to right side of the room. The orifi has a diameter of 100mm and is under the surface of oil, 4m from the surface on the left and 1.6m from the surface on the right. The surface at the left is under 50KPA of pressure and the surface at the right side is under 10KPA of pressure. Determine the actu discharge in the orifice if C = 0.92

Name: ...P1 = 50 KPaP2 = 10 KPa4mOIL1.6mOILIn the figure, an orifice is loc
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: ...P1 = 50 KPaP2 = 10 KPa4mOIL1.6mOILIn the figure, an orifice is locates in the partition wall so that it discharges oil (SG = 0.8) from left to right side of the room. The orifice%3Dhas a diameter of 100mm and is under the surface of oil, 4m from

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. An open trapezoidal tank is accelerated horizontally at 6m/s2 along its length. Its bottom width is 4.20m and its sides are inclined at 3H:4V. If it has a height of 3m, width of 2m and it is filled with water at a height of 2.5m, how much water is spilled out in m3.. 2. A cylindrical shape solid container of sg=0.515 having a diameter of 1.5m and a height of 3.10m is floating in a seawater of sg=1.03. Attached at the bottom of the container is a steel ball of sg= 7.85. If the height of the container projecting above the fluid surface is 0.60m. Determine the diameter in m and weight in KN of the steel ball.
Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A is 35 cm above the pipe B. The height of oil in right limb is 40 cm. Also, the mercury level difference is found in right limb as 80 cm. Find 1-The difference of pressure between two pipes (PA-PB) (Unit is in kPa) = 2-Equivalent to Water head in mm =
Qz: A A liquid of (N = 1:25 Pais.) fills the space of (Sum) shown in figure below. Calculate the forque (T) required to rotate the frustum cone at a constant speed of a (60 rip.u). IT Smm o. 3m 0.7m
If you have a closed system that is filled with water on 2bar, the pump is selected for pressure losses due friction of the pipes(1bar) 1/ why don't we have to take pressure losses due height in account? 2/ what is the pressure at 100 m height inside the system? When the pump stops? And when the pump is circulating, prove your answer figure in image
5. For the setup shown in the figure, what is the pressure pA if the specific gravity of the oil is 0.82? (S.G. of Hg 13.6) Air Oil Орen 4 m H,0 320 mm Hg- Figure for Prob. No. 5
Water [2] the diameter of a cylindrical water tank is Do and its height is H. The tank is filled with water, which is open to the atmosphere. An orifice of diameter D with smooth entrance (i.e., no losses) is open at the bottom. Develop a relation for the time required for the tank (a) to empty halfway and (b) to empty completely. Tak Des Onfice Hole Water out
Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A is 65 cm above the pipe B. The height of oil in right limb is 35 cm. Also, the mercury level difference is found in right limb as 50 cm. Find the pressure difference between these two pipes in kPa. Also find the pressure equivalent in water head in mm. -The difference of pressure between two pipes (PA-PB) (Unit is in kPa) = -Equivalent to Water head in mm =
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 110 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.9 and sp. gr of oil = 0.9Difference in pressure head (unit in m) =Velocity of flow (unit in m/s) =
b) An inverted differential manometer is connected to two pipes A and B w The fluid in the manometer is oil of specific gravity 0.8. For the manome in fig. Q 2, find the pressure difference between the two pipes. 18-424 5-8- Ponnant OIL OF Sp. gr. 0.8 -x diⱭMAO OT anс
liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp
Answer the following question: 1. Water flows through a horizontal pipe at a velocity of 30 ft/s, flowing to the pipe narrows down to smaller size, the velocity increases to 60 ft/s. What is the difference between the pressures at two points?
Water is contained in both sides of the cylinder system shown below and the valve is closed. If the pressure on the right hand side of the valve is 119.6 kPa, what is the height in tank B, i.e. what is hp 1? Assume that the atmospheric pressure is 100 kPa, the acceleration due to gravity is 9.807 m/s² and the density of water is 1000 kg/m³. A Po B ha,1=1.5 m Water Water hg,1 1.0 m 0.5 m Pval,left Pyal,right A) 1.0 m B) 1.5 m C) 2.0 m D) 2.5 m