_ * G ۱۱:۲۳H.W.JPG →A.wteaIn an FM system, the modulating frequeng Em = 1kHthe modulating voltage Um = 2 volt, and the deviationIS GKHZ. If the modulating Voltage is raised to4 volts, what will be the new deviation?.m1If the modulating voltage is further increased.the modulating frequency is reduced500 Hz, what will be the deviation ?to8 velts andFind the modulation inded in each case?an FM signalwhat will be the Bw required forif the modulating frequency is 1KHZ & maximum,deviation is 10 KHZ? what is the Bw required.for the corresponding DSB AM transmission?3 A 20 MHZ Carrier is modulated by a 400 Hz5V andlo kHz. write thewaves.modulating signal. The carrier voltage ismaximum deviation ismathematical expression for FM & APMIf the modulating frequency is increased to 2KHZkeeping every thing else constant.In an FM system, the audio frequency is 1KHZ andthe audio voltage is 2v. The deviation is 4 KHZ. Ifthe audio voltage in creased to 8 volt and audioFree droped to 500 Hz. Find the modulation index.Carson's rule.in each case and Bw using:=|||U1=1

In this question we have given FM modulation....We have to find out deviation and modulation…

... H.W.JPG A.W Em In an FM systems the modulating frequeng the modulating voltage Um = 2 volt, and the devin => 6KHZ. If the modulating Voltage is raised. 4 volts, what will be the new deviation?. to If the modulating voltage is further increase 8 volts and the modulating frequency is re 500 Hz, what will be the deviation ? Find the modulation index in each case? what will be the Bw required for the Bw required for an FM sign if the modulating frequency is |KHZ & maximu the Bw requir

... H.W.JPG A.W Em In an FM systems the modulating frequeng the modulating voltage Um = 2 volt, and the devin => 6KHZ. If the modulating Voltage is raised. 4 volts, what will be the new deviation?. to If the modulating voltage is further increase 8 volts and the modulating frequency is re 500 Hz, what will be the deviation ? Find the modulation index in each case? what will be the Bw required for the Bw required for an FM sign if the modulating frequency is |KHZ & maximu the Bw requir

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How to calculate the efficiency in frequency modulation and what is the highest value for efficiency in frequency modulation
What is the problem with AM signal when overmodulation occurs?
Construct MOD 12 asynchronous counter. What will be the output frequency, if the input frequency is 1 MHz. If the counter is at state 6, what will be the count after 60 pulses.
A second modulating tone having the same amplitude but a different frequency is added to the first at the input to the modulator. THE MODULATION INDEX WILL BE INCREASED VY HOW MUCH??
Q1-Derive the effect of phase and frequency errors between the local oscillator signal and the received SSB carrier signal in the synchronous SSB detector. 2.09
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.48 V respectively. The form factor of this circuit is ___________________.
7- When does over-modulation occur? a) Modulating signal voltage carrier voltage c) Modulating signal voltage = carrier voltage d) Modulating signal voltage = 0
Write an 8051 ASM program to load the timer 1 in order to generate 2000 Hz square wave as given in Figure. The square wave should be generated on pin 2 of port 3. Assume the crystal frequency is 16 MHz. ON 4* Delay Delay
-Fill in the blank(s) with appropriate word(s): 1. The three –phase half - wave converter is not normally used in practical systems, because ___________________.2. The three –phase half - wave converter is provide _______________average output voltage.3. The frequency of output ripple voltage for three –phase half - wave converter is_____________.
3) What are advantages and disadvantages for center tap and bridge? 4) What is difference between half wave and full wave circuits? 5) What is ripple factor? 6) What is happen when increase or decrease capacitor value?
Determine four distinct types of modulation processes.
Q2/ One input to an AM DSBFC modulator is an 800 kHz carrier with an amplitude of 40 vp. The second input is a 25 kHz modulating signal whose amplitude is 1O vp. Determine a. Upper and lower side frequencies b. Modulation coefficient and percent modulation c. Maximum and minimum positive peak amplitude of the envelope d. Draw the output frequency spectrum e. Draw the envelope