What is the lowest allowable dimension for the flats?

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: show FBD

A: As per question asked below is the FBD of the given problem

Q: Minimum thickness?

A: Given; A building has to be maintained at, TI=210 C (DB)Wet bulb, Tdb=10.170COutside temperature,…

Q: mensions a tonnage to E the part if the desity

A: Given compaction pressure = 1000 MPa Surface area of the component = π4652- 202 mm2 We know that Pr…

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: the largest internal normal force in

A: To find largest internal normal force in  the bar

Q: What is the internal axial force?

A: Internal Axial Force is defined as the force acting in the direction parallel to the axis of the…

Q: What is the springs free length(ft)?

A:

Q: what is the measured distance to the nearest eigthth between the outside corners of the tongue and…

A: FRAMING SQUARE  A framing square, also known as a steel or carpenter square, can be the most…

Q: mum weight of cylinder th your answer in two decimal

A: given:

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: ust be from the origin. 70 mm mm 60 mm 10 mm

A: Area symbol area mm2 x̄(mm) ȳ (mm) A x̄(mm3) A ȳ (mm3) A1 40*15=600 -62.5 27.5 -37500…

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: The nominal diameter of V00 bolt is diameter. If safe tensile stres of the bolt

A:

Q: if the f Re 20 -0.25 mm %3D De terminef?

A: Relative roughness, eD=0.25Reynolds number, Re=20

Q: bend allowance is

A: Given: Metal sheet thickness is =2 mmIt is to be bent at an angle of one radian,Bent radius is= 100…

Q: , the minimum metric specification required for the bolt is

A: Given, From the given shows,  Three bolt system having, Shear yield strength,σyt=200 MPaFOS=…

Q: (8 – x) . 5 in. Dy -2 in.

A:

Q: of Appendix D as needed. spacec equal

A: we have to determine the distance where the two forces become equal

Q: The minimum possible thickness

A: Given; A thick sheet having 4 mm is rolled with 300 mm diamaterOr, d=300 mm t=4 mmFriction…

Q: Q3. What is "Hardness" and how it can

A: ◆The hardness is defined as, "the ability of the material that can resist indentation or scratch or…

Q: If the shaft is always smaller than the hole, general fit name is Fill in the blank with correct…

A: If the shaft is always smaller than the hole, general fit name is_______________. Answer: D)…

Q: H.W praw load dingram alesfanding to the given-Shar dingram? 2nd (urve 10 2nd Garve sfin -10 Im Im

A: BMD(Bending moment diagram) is a diagram representing the variation of bending moment along the…

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

A:

Q: 250mm 250mm Reinforcing Bars

A:

Q: 600 mm C 360mm

A:

Q: ___________ tool is used for verifying the flatness of the component.     A. Protractor…

A: Protractor is a device used to measure the angles. Engineers square is a checking tool which is used…

Q: On increasing the value of rake angle, the strength of tooi.

A: Rake angle is defined as the angle between the normal line to the workpiece and the edge of the…

Q: The largest soft aluminum tubing that may bent by hand is ________________ -inch outside diameter. *

A: Solution:

Q: The rim offset is the vertical distance between the rim centerline and the    of the disc.

A:

Q: What is the average force magnitude?

A:

Q: what maximum angle can the ramp make with the horizontal before the block starts to slip down?

A:

Q: What is the Falling Block?

A: Falling block: The falling block is an action in which a solid metal slides vertically in a grove…

Q: grees sideways. AB-20, BC-25, CD-30, 8D-50, CF-4Scm. Draw in appropriate scale

A:

Q: What is the sliding block?

A: To Define: Sliding block

Q: Which distance represents height of the fall for measurement of the time?

A: In the question, a machine is given and when it rotates it is needed to find out the height and time…

Q: What was the orginal size of the smallest outside diameter?

A: Data given-

Q: The denomination for a force or shrink fit in the US system is ?

A: Solution:

Q: 12. How much wall thickness is there between the counterbore and the sides of the counterweight?

A: T=0.063 Answer

Q: State any THREE conventions in dimensioning.

A:

Q: ow bar evaluate use th

A:

Q: On the part above, there is no perpendicularity requirement specified between the right surface and…

A: Whenever a control feature frame is applied to a drawing, it needs to have some reference. The…

Q: What is the counterclockwise angle?

A: The counterclockwise angle is the angle measured in the opposite direction of the clock.

Q: 4. What is the length of the longest part?

A: To find Length of longest part.

Q: ving a length of of the specimen?

A: Given data Length of the specimen = 100mm elongation of specimen = 5mm Load on specimen = 10,000N…

Q: What is the depth, minor diameter, width of crest and root for a bolt 1⁄2 X 20 UNF

A: UNF = Unified National Fine Screw Thread.   The Nominal Major Diameter and Threads-per-inch (Pitch)…

Q: The appropriate diameter is mm.

A: To find  diameter

Q: 1. Is the 'fit' between the 2 parts shown below a clearance fit or interference fit ? 2. Which…

A: