The sign is subjected to the uniform wind loading with the pressure 1.75 kPa. The supporting post has a circular cross-section with a radius of 50 mm. At the cross-section shown in the figure, Click here to see all formulas 3 m Part A - Determine the shear stress at point A in MPa O 26.7 O 13.4 O 22.3 O 8.91 O 17.8 Submit Request Answer Part B - Determine the shear stress at point B in MPa O 6.89 O 20.7 O 10.3

The sign is subjected to the uniform wind loading with the pressure 1.75 kPa. The supporting post has a circular cross-section with a radius of 50 mm. At the cross-section shown in the figure, Click here to see all formulas 3 m Part A - Determine the shear stress at point A in MPa O 26.7 O 13.4 O 22.3 O 8.91 O 17.8 Submit Request Answer Part B - Determine the shear stress at point B in MPa O 6.89 O 20.7 O 10.3

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.4P: A circular pole is subjected to linearly varying distributed force with maximum intensity t0....

See similar textbooks

Similar questions

A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum shear stress at point A on the cross section of the bracket at section a-a. Calculated for you: Iz = 0.79948 in“, cross sectional area is 0.875 in². 0. in. 0.25 in. 0.25 in---|-0.25 in. 6 in. I.s in'1.5 in. L Section a-a 12 in.
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.89 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. O 42.6 ksi O 31.2 ksi O 39.7 ksi O 36.1 ksi O 33.5 ksi
20 A force of 250 kN was needed to punch the hole through the 8 mm thick steel plate, as shown below. rosesloyotoled jau milubase Ø24 Farhododecirl most soumis SALP30 TOUREN stav (A) 76.11 MPa (B) 97.66 MPa (C) 203.75 MPa (D) 399.06 MPa Hora 100 39 Calculate the ultimate shear stress of the steel plate. 60 bobini dignoue Mould 10.00 (0) gnitroo ni beau Pefore on OV1 es des anglet of quilida fins lidi.is (8) constalter goisons (2) in boe migjow tigilan (0)